FallTech 744410 single-use wood roof ridge anchor 10-pack
FallTech

FallTech 744410 Single-Use Roof Ridge Anchor, 10-Pack

(No reviews yet) Write a Review
$103.00
Brand:
FallTech
SKU:
744410
Availability:
Usually ships in 1 business day
Shipping:
Calculated at Checkout
Adding to cart… The item has been added
American Express Icon American Express Icon Discover Icon Discover Icon Mastercard Icon Mastercard Icon PayPal Icon PayPal Icon Visa Icon Visa Icon
FallTech Anchorage Connectors

FallTech 744410 Single-Use Wood Roof Ridge Anchor (10-Pack)

The FallTech 744410 is a 10-pack of single-use wood roof ridge anchors. Each economical nail-down anchor installs at the roof ridge for a temporary tie-off point during construction, and the 10-count pack keeps a crew supplied on a new roof.

Each anchor meets OSHA fall protection requirements for one worker, and the pack is the economical way to stock ridge anchors for a job.

FallTech 744410 single-use wood roof ridge anchor 10-pack
10-PackContractor Pack
Single-UseNail-Down Ridge Anchor
OSHACompliant
1 WorkerPer OSHA
Wood RidgeRoof Mount
EconomicalLow Cost Per Unit
TemporaryConstruction Use
RoofingNew Construction

Who Needs This Product

This product is a 10-count pack of single-use wood roof ridge anchors for new roof construction. Roofers nail each anchor at the ridge for a temporary tie-off point, then connect an SRL or lanyard. Each is a low-cost, single-use anchor left in place. You still need a certified full-body harness and a compatible connecting device.

Features

10-count pack

Keeps a crew supplied with ridge anchors on a new roof.

Single-use economy

Low per-unit cost so you can set anchors freely.

Ridge install

Each anchor nails at the roof ridge for a central tie-off.

Wood roof mount

Fastens to ridge framing with the specified nails.

Left in place

Not removed for reuse; stays with the completed roof.

OSHA compliant

Each anchor meets the OSHA anchorage requirement for one worker.

⚠

Nail each anchor to sound ridge framing, single use only. Drive all required nails into solid wood at the ridge per the manual, and do not reuse an anchor. Confirm fall clearance and swing-fall with the Fall Protection Calculator below.

Compliance Standards

OSHA compliant

Meets OSHA fall protection anchorage requirements. Not ANSI-certified.

OSHA 29 CFR 1926.502

Federal construction fall protection anchorage requirements.

OSHA 29 CFR 1910

General industry personal fall protection requirements.

3,600 lb Min Tensile Strength

Zinc plated carbon steel with a 3,600 lb minimum material tensile strength, static tested above 3,600 lbf for one minute in FallTech lab testing to OSHA 1926.502.

Typical Applications

New roof constructionBulk temporary tie-offs during the build.
Production roofingEconomical anchors in quantity.
Residential roofingRidge anchors for house roofs.
FramingTie-off during roof framing.
TrussesAnchors along the ridge line.
SheathingTie-off while decking the roof.

How to Install

Follow the FallTech instruction manual. The sequence below is an overview only.

  1. Inspect. Check the anchor body, connection point, and hardware for damage before each use.
  2. Prepare the structure. Confirm the mounting surface is sound and rated to support the anchor per the manual.
  3. Install and secure. Mount the anchor as specified and set all fasteners to the required torque.
  4. Connect. Attach your SRL or energy-absorbing lanyard to the connection point.
  5. Check clearance. Confirm fall clearance and swing-fall with the calculator below.

Inspection and Retirement

Inspect before each use, with a documented competent-person inspection at least annually. Remove the anchor from service for any of the conditions below.

  • Anchor body and welds: cracks, bending, deformation, or corrosion.
  • D-ring or connection point: deformation, sharp edges, cracks, or corrosion.
  • Fasteners and hardware: damaged threads, loose or missing fasteners.
  • Labels: illegible or missing markings.

Remove the anchor from service immediately after any fall-arrest event, and destroy retired equipment so it cannot return to service.

Fall Protection Distributors logo Fall Protection
Distributors, LLC Free Tool · No Signup · OSHA 1926.502 Free Interactive Tool Fall Protection Calculator Pick your system. Run the math. Generate a plan. 1Pick Your SystemDetermine fall restraint vs. fall arrest based on your work surface, edge access, and clearance. 2Run the MathCalculate exact fall clearance required below the work surface for your lanyard or SRL setup. 3Generate a PlanGet a printable OSHA-compliant Fall Protection Plan structured around 29 CFR 1926.502(k). Run the Numbers and Stay Safe Launch the Calculator ›

Technical Specifications

TypeSingle-use wood roof ridge anchor, 10-pack
Quantity10 anchors per pack
MountingNail-down at the roof ridge
ComplianceOSHA
Material tensile strength3,600 lb minimum, per the FallTech manual
CapacityOne worker, up to 310 lb combined (OSHA)
StandardsOSHA 1926.502 and 1910
WarrantyFallTech 2-year limited warranty against defects in materials and workmanship

Frequently Asked Questions

What is in the 744410 pack?
Ten single-use wood roof ridge anchors, the economical pack for stocking a new roof job.
Are the anchors reusable?
No. Each is a single-use anchor nailed at the ridge and left in place; do not remove and reuse.
Where do they install?
At the roof ridge, each nailed into sound framing per the manual.
Is it ANSI certified?
They are not ANSI certified. Each anchor meets OSHA 1926.502 for one worker up to 310 lb, and the manual lists a 3,600 lb minimum tensile strength for the zinc plated carbon steel anchor. Confirm it fits your fall protection plan.
Can I buy a single instead?
Yes. The 7444 single-use ridge anchor is also sold individually in multi-packs.
What do I connect to it?
Connect a compatible SRL or energy-absorbing lanyard to the connection point, used with a certified full-body harness.
Can it be reused after a fall?
No. Remove the anchor from service immediately after any fall-arrest event and destroy it so it cannot be reused.

FallTech 744410 Submittals and Documentation

744410 Instruction Manual (PDF)Installation, capacity, and inspection. 744410 Declaration of Conformity (PDF)Certification to OSHA requirements (FallTech test lab). 744410 Spec Sheet (PDF)One-page specifications summary.

Related Anchors

Specifying Anchors for Your Crew?

The anchor, the connecting device, and the harness all have to match the structure and the fall clearance below. Confirm your application with us and we will help you choose the right anchor.

Call 863-703-4522 to talk to a fall protection specialist.

FallTech 2-Year Limited Warranty. FallTech warrants to the buyer that all products are free from defects in material and workmanship at the time of shipment. Obligation is limited to product replacement for two (2) years from the date of installation or use by the owner, not to exceed two (2) years from the date of shipment. This warranty is not transferable and is void if the product is changed, altered, or used in a manner other than intended. It covers defects in material and workmanship only; it does not cover normal wear and tear, neglect, abuse, or accident. The limited warranty is provided only to an end-user customer for the period set forth in an order that has been accepted by Fall Protection Distributors, LLC. The end user customer must be: (a) a Buyer purchasing product directly from Fall Protection Distributors, LLC or Buyer of product purchasing from an authorized reseller. The limited warranty covers defects in materials and workmanship in the FallTech product. The limited warranty does not cover problems resulting from external causes such as accident, abuse, misuse, servicing not authorized by Fall Protection Distributors, LLC, usage that is not in accordance with product instructions, failure to follow the product instructions or failure to perform preventive maintenance, problems caused by using accessories, parts, or components not supplied by Fall Protection Distributors, LLC; normal wear and tear; and products with missing or altered service tags or serial numbers. FALL PROTECTION DISTRIBUTORS, LLC’S RESPONSIBILITY FOR MALFUNCTIONS AND DEFECTS IN PRODUCT IS LIMITED TO REPAIR AND REPLACEMENT OF THE PRODUCT AS SET FORTH IN THIS WARRANTY STATEMENT. EXCEPT AS PROVIDED ABOVE, FALL PROTECTION DISTRIBUTORS, LLC AND ITS SUPPLIERS MAKE NO, AND HEREBY DISCLAIM ALL OTHER, WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
0 Reviews Hide Reviews Show Reviews

About FallTech

FallTech is a well-known brand that provides reliable fall protection solutions. Based in Compton, CA, it is committed to maintaining every product's highest safety and quality standards. FallTech is an accredited manufacturer under ISO 9001:2015 and has an in-house test lab accredited under ISO 17025, which ensures that every product undergoes rigorous testing to comply with ANSI, C.S.A., and OSHA standards. Their product range includes full-body harnesses, shock-absorbing lanyards, anchors, and self-retracting lifelines (S.R.L.s), all designed and built in the U.S.A. to minimize exposure to fall arrest forces. FallTech is a brand dedicated to saving lives through superior fall protection engineering and uncompromising quality. One of their core values is to "never overpromise, yet always overdeliver." Many customers ask for FallTech products by name, and substitutions are prohibited. The brand has a reputation for providing comprehensive fall protection solutions that meet the highest safety standards and is committed to delivering on its promises.

Related Products

!