SSRA1 Standing Seam Roof Anchor—The Industry's Most Versatile Non-Penetrating Tie-Off Solution
The SSRA1 Standing Seam Roof Anchor weighs just 4.5 pounds and installs in approximately 2 minutes with a micro-torque wrench. This device provides 5,000-lb certified fall protection without requiring any panel penetrations. Contractors, solar installers, maintenance crews, building owners, and even DIY homeowners trust the SSRA1 to deliver safe, code-compliant tie-off points while preserving the warranties and watertight integrity of the standing seam roof systems.
SSRA1 Standing Seam Roof Anchor Third-Party Testing
Independent ISO 17025/ANSI Z359.18 testing confirmed the SSRA1 Standing Seam Roof Anchor's unmatched strength and reliability.
While OSHA and ANSI require anchors to withstand 5,000 lbs., the SSRA1 endured an astonishing 14,500 lbs. before the Grade 8 top bolts sheared—leaving the solid aluminum body completely unharmed. This performance not only exceeds industry standards but also surpasses competitors', proving that the SSRA1 is in a league of its own.
▶ SSRA1 Compatibility Overview
This Panel Compatibility Chart is provided only as a reference for what the SSRA1 will physically mount to. It does not determine the structural integrity of any roof system or seam. It is the Competent Person's responsibility to verify structural suitability in the event of a fall. The SSRA1 fits over 95% of standing seam panels. It is approved only for 22- and 24-gauge steel and is not compatible with aluminum, zinc, copper, or other soft metals. Do not install on curved, tapered, or batten-seam profiles.
▶ Nailstrip Panel Warning
Nailstrip-style panels are approximately 50% compatible. Some seams are too wide at the base, which can allow anchor movement during installation. Treat compatibility lists as guidelines, not guarantees.
▶ Installer Responsibility
The employer and the designated Competent Person are solely responsible for evaluating, determining, and documenting the structural suitability of the supporting structure. The manufacturer assumes no responsibility for structural assessment or performance under load.
▶ Test Fit Recommendation
Perform a test fit with an RCT seam clamp well before installation.
▶ Set-Screw Options
- Cupped-tip: 22-gauge steel—torque to 90 in-lbs
- Nylon-tip: 22/24-ga steel—torque to 180–200 in-lbs
▶ Surface Impact
Minor seam dimpling and paint abrasion may occur. Scratches can be touched up with a matching paint pen.
SSRA1 Standing Seam Roof Anchor Patented Non-Penetrating Design
The SSRA1 Standing Seam Roof Anchor features a patented design with a solid 6061-T6 aluminum body secured by 12 stainless steel set screws.
This system provides a rock-solid attachment without damaging the seam. Unlike compression-style anchors that rely on plates to squeeze the seam with high torque, the SSRA1's set screws prevent sliding during impact and deliver consistent holding power at much lower torque settings.
Each SSRA1 comes standard with a 5,000-lb certified D-ring for single-worker tie-off. The universal-fit SSRA1 anchor body adapts to more than 500 standing seam panel profiles—including T-seams, bulb seams, SnapLok, MR-24, single lok, and double lok—without requiring reassembly.
The SSRA1 has a unique removable D-ring, making it compatible with adapter plate components. The SSRA2 Adjustable Roof Jack Adapters mount on top of the SSRA1 to support 10-foot walkboards. Contractors can use the SSRA3 Anchor Plates connected to SSRA1 anchors to create temporary 100-foot horizontal lifeline systems.
Check out our unboxing video above to see exactly what is included when you receive your SSRA1 Standing Seam Roof Anchor.
SSRA1 Standing Seam Roof Anchor Benefits for Fall Protection
- Weighs only 4.5 lbs.—the world's lightest OSHA/ANSI 5,000-lb tested roof anchor
- Installs in minutes with a micro torque wrench and 3/16" hex bit socket
- The universal-fit design works on over 500 standing seam panel profiles
- Non-penetrating installation protects roof warranties and watertight performance
- OSHA-tested to 5,000 lbs. in all directions, ensuring safety on both sides of the roof
- Made in the USA from durable aluminum and stainless steel, compliant with ANSI/ASTM B-117 salt spray resistance
- Clean, low-profile installation reduces tripping hazards on the jobsite
- Includes a Limited Lifetime Warranty
SSRA1 Standing Seam Roof Anchor Applications
The SSRA1 Standing Seam Roof Anchor is a versatile solution for many safety applications.
Workers can use it for attaching roof jacks for 10-foot wooden walkboards, self-retracting lifelines (SRLs), horizontal lifelines, and ladder anchoring. Workers using SSRA1 anchors must use inline shock absorbers or shock packs. For 22-gauge panels, both cupped-tip and nylon-tip set screws are available, whereas 24-gauge panels require only nylon-tip set screws.
What's Included with the SSRA1 Standing Seam Roof Anchor
- 12" solid 6061-T6 aluminum body with patented universal-fit design
- 5,000-lb certified forged D-Ring
- 12 stainless steel cupped-tip set screws (3/16" hex/Allen)
- Limited Lifetime Warranty
- Owner's Manual for SSRA1 Seam Anchors
Additional SSRA1 Anchor Resources
SSRA1 Cut Sheet | SSRA1 Spec Sheet | SSRA1 Owner's Manual
SSRA1 Frequently Asked Questions
Will the SSRA1 Standing Seam Roof Anchor damage my roof panels?
No. The SSRA1 is a non-penetrating system. It uses 12 stainless steel set screws to clamp onto the seam rather than compression plates that crush the metal. While minor dimpling or paint abrasion may occur at the contact points, the panel's structural integrity, thermal expansion ability, and watertight warranty remain intact.
How many different standing seam profiles does the SSRA1 fit?
The SSRA1 is the industry's most universal anchor, designed to fit over 500 different standing seam profiles, including T-seams, bulb seams, SnapLok, MR-24, and trapezoidal Double-Lok panels, without requiring additional adapters.
What is the certified strength of the SSRA1 anchor?
The SSRA1 is OSHA and ANSI Z359.18 certified for 5,000 lbs. in any direction of pull. In independent laboratory testing, the anchor body withstood loads up to 14,500 lbs. before failure, far exceeding federal safety requirements.
Can the SSRA1 be used for temporary or permanent installations?
The SSRA1 is highly versatile and can serve as a temporary tie-off point for short-term projects or a permanent fall protection solution for facility maintenance. Its salt-spray-resistant construction ensures long-term durability in all environments.
Do I need to use a shock absorber with the SSRA1?
Yes. To remain compliant and ensure worker safety, all personal fall arrest systems attached to the SSRA1 must include an inline shock absorber or a shock pack to limit the arresting forces on the anchor and the user.
Is the SSRA1 Standing Seam Roof Anchor made in the USA?
Yes. The SSRA1 is proudly developed, tested, and manufactured in the USA. This ensures strict quality control and compliance with domestic safety standards that cheap imported knockoffs cannot guarantee.
How do I avoid common installation problems like over-tightening or panel damage?
Achieving a 100% safe installation requires following three critical rules:
- Never Use Impact Drivers: Over-tightening with power tools can crush the seam or strip threads. Always use a calibrated micro torque wrench set to 90 in-lbs (cupped) or 180-200 in-lbs (nylon).
- Verify Gauge & Substrate: The SSRA1 is strictly for 22- or 24-gauge steel. Using it on softer substrates like copper, aluminum, or zinc is prohibited. For soft metals, use the Ridge Pro Steep Assist.
- Replace Consumables: Nylon-tipped set screws must be replaced every 3-5 uses to maintain the required coefficient of friction.
-
Roof Anchor
I ordered several of these and the delivery was prompt and everything was in good shape
