10-Pack · Stock Your Crew Single-use or reusable wood-truss roof anchor for residential roofs from 0/12 to 4/12 pitch. Sold in 10-packs so roofing contractors can stock crew trucks and framers can buy enough for an entire job in one click. ASTM A36 steel, 5,000 lb minimum breaking strength, ANSI/ASSP Z359.18-2017 certified by Intertek — available in Galvanized, Black, or Green.
Buy 5+ ten-packs — save $10 per pack at checkout. Order 50+ anchors (five 10-packs or more, any combination of colors) and the bulk discount applies automatically. $50 off a 5-pack order, $100 off a 10-pack order.
5,000lb Breaking Strength
1.4lb Per Anchor
10 Anchors Per Pack
4/12 Max Roof Pitch
12 Fasteners To Install
Why Roofing Contractors and Framers Buy the RORS01 by the 10-Pack
Single roof anchors are an inventory headache. By the time you remember to reorder, you're already on the next job. The Frontline RORS01 in a 10-pack solves both sides of that problem: roofing contractors stock crew trucks so the next tear-off, re-roof, or repair job has anchors ready before sunrise. New-construction framers and GCs can buy enough for an entire production house, a multi-unit roof, or an addition in a single transaction.
At 1.4 lbs per anchor and just 3" × 11.4" × 1/2", ten anchors fit in a small toolbox. Twelve fasteners (Grip-Rite 3.5" exterior screws or 16D galvanized framing nails) install each anchor in minutes with no special tools. When the job is done, the anchor stays as a permanent tie-off point or comes off with the temporary roof system — reusable, your call.
Available Colors — Choose Your Finish
Same anchor, same certification, same 10-pack pricing. Pick the finish that matches your roof, blends with shingles, or color-codes your crew gear. Need to mix colors? Add a 10-pack of one color, then a 10-pack of another to your cart — combine as many as you need. The bulk discount stacks across colors.
Galvanized Hot-dip finish, raw industrial look
Black Electrostatic paint, blends with dark shingles
Green Electrostatic paint, blends with weathered roofs
Key Features of the Frontline RORS01 PitchFast Roof Anchor
- Low-Profile Design (1/2" Thick)Stays out of the way during shingle installation and re-roofing work, with no awkward tear-around when you're done.
- ASTM A36 Steel Construction5,000 lb minimum breaking strength — meets the 5,000 lb minimum required by OSHA 1926.502(d)(15).
- Type A Single-Point AnchorTested to ANSI/ASSP Z359.18-2017 by Intertek (NRTL), Report No. 105938082CRT-003 — certified for both fall arrest and work positioning.
- Twelve-Fastener InstallUse either (12) 3.5" Grip-Rite exterior screws or (12) 16D galvanized framing nails. A minimum of 8 must engage the structural wood truss; the remaining 4 must be in sheathing.
- Wood-Truss Substrate RequiredDesigned specifically for residential wood-frame construction. Substrate must be a structural wood truss, minimum 3.5" thick.
- Reusable or Single-UseRemove with the temporary roof system or leave as a permanent tie-off for future maintenance and inspections.
- Lightweight — 1.4 lbs EachA 10-pack weighs under 15 lbs — fits in a tool tote, tucks in a truck box, ships flat-rate friendly.
- Wide Service Range-30°F to +130°F means it ships, stores, and works year-round across every U.S. and Canadian climate zone.
Technical Specifications
| Specification | Detail |
|---|---|
| Model | Frontline RORS01 PitchFast Residential Roof Anchor |
| Anchor Type | Type A (single-point), tested per ANSI/ASSP Z359.18-2017 |
| Pack Quantity | 10 anchors per pack (single color per pack) |
| Color Options | Galvanized, Black, or Green |
| Breaking Strength | 5,000 lbs minimum |
| User Capacity | 1 person, 310 lbs maximum combined weight |
| Material | ASTM A36-rated steel |
| Finish | Hot-dip galvanized, or black/green electrostatic paint |
| Dimensions | 3" × 11.4" × 1/2" |
| Weight (each) | 1.4 lbs |
| Roof Pitch Range | 0/12 to 4/12 (low slope only) |
| Working Angle | Up to 15°, anchor parallel to the user, facing the fall hazard |
| Substrate | Structural wood truss, minimum 3.5" thick |
| Fasteners Required | (12) 3.5" Grip-Rite exterior screws OR (12) 16D galvanized framing nails per anchor |
| Fastener Engagement | Minimum 8 into the structural truss; remaining 4 may engage sheathing |
| Maximum Free Fall | 6 ft per OSHA 1926.502 / ANSI Z359.11 |
| Service Temperature | -30°F to +130°F |
| Use | Temporary or permanent — reusable |
| Test Lab | Intertek Testing Services NA Inc., Cortland, NY |
| Test Report Number | 105938082CRT-003 (Issued September 27, 2024) |
| Test Date Range | September 23–24, 2024 |
| Designed By | Frontline Fall Protection Inc., Miami, FL |
| Manufactured In | Colombia (quality-managed production) |
⚠ Roof Pitch — Read Before Ordering
The RORS01 is rated for residential roofs with a pitch of 0/12 to 4/12 (low-slope only). It cannot be used on pitches steeper than 4/12 or on standing-seam metal roofs.
For roof pitches above 4/12, you need a different anchor designed for steep-slope residential work. For standing-seam metal roofs, use a non-penetrating, clamp-on anchor such as the SSRA1. Not sure what applies to your project? Call us at 863-703-4522 before you buy.
Compliance & Certification
✔ Certified ANSI/ASSP Z359.18-2017 U.S. anchorage connector standard for single-point anchors. Independently certified by Intertek (NRTL) at their Cortland, NY facility under Report No. 105938082CRT-003.
✔ Compliant OSHA 1926.502(d) Construction industry fall protection. Meets the 5,000 lb anchor strength minimum and 2:1 safety factor requirements for personal fall arrest systems.
✔ Compliant OSHA 1910.140 General industry personal fall protection systems criteria, applicable to maintenance, service, and repair work outside the construction context.
✔ Compatible Canadian Provincial OHS Suitable for residential roof work in Ontario, BC, Alberta, and Quebec when paired with CSA Z259-compliant harness, lanyard, and SRL components per provincial regulations.
Independently Tested by Intertek Testing Services NA Inc. Intertek is a globally recognized third-party testing laboratory and Nationally Recognized Testing Laboratory (NRTL). The RORS01 was tested at Intertek's Cortland, NY facility on September 23–24, 2024. All required tests passed: design requirements, pre-conditioning, dynamic strength on Type A wood substrate (MAF up to 3,104 lbs across three samples), residual dynamic strength, static strength (5,000 lb test load held 3 minutes with no deformation greater than 1/8"), and marking and instructions. Testing completed by Alex Smith (Technician), reviewed by Matthew Stevens (Team Leader). Test Report No. 105938082CRT-003 | Issued September 27, 2024 | Available below
How to Install the Frontline RORS01 PitchFast Roof Anchor
The RORS01 installs in minutes with hand tools or a framing nailer. Follow the manufacturer's user manual for full instructions and always inspect the anchor before each use.
Tools & Supplies NeededDrill driver or framing nailer; pitch gauge or smartphone level; (12) 3.5" Grip-Rite exterior screws OR (12) 16D galvanized framing nails per anchor.
- Confirm Roof PitchVerify the roof pitch is between 0/12 and 4/12. Do not install on roofs steeper than 4/12 — the anchor is not rated for steeper pitches.
- Locate a Structural Wood TrussIdentify a wood truss, minimum 3.5" thick. The anchor must be installed directly over and into the truss, not into sheathing alone.
- Position the AnchorPlace the RORS01 with the connection point parallel to the user's path of travel and facing the fall hazard. The anchor must be positioned so the working angle stays within 15°.
- Drive 12 FastenersUse either (12) 3.5" Grip-Rite exterior screws or (12) 16D galvanized framing nails. A minimum of 8 fasteners must engage the structural wood truss; the remaining 4 may anchor into the sheathing.
- Inspect ConnectionsVerify all 12 fasteners are fully driven, the anchor sits flush, and there is no gap between the anchor base and the roof surface.
- Connect Fall ProtectionAttach a compatible self-retracting lanyard or shock-absorbing lanyard to the connection point. Confirm that total fall clearance below the work surface accounts for free fall (6 ft max), deceleration distance, harness stretch, and safety margin.
- Inspect Before Each UseBefore every shift and after any fall event, inspect the anchor, fasteners, and connection point for deformation, corrosion, or damage. Remove from service if any issue is found.
Frequently Asked Questions
Why is the RORS01 only sold in 10-packs?
Roofing crews and framers rarely need just one anchor. A typical residential roof uses several anchor points, and contractors stocking crew trucks need backup units on hand. Selling by the 10-pack is more economical for the buyer and lets us keep shipping fast and support strong. Buying five 10-packs (50 anchors) or more triggers an automatic $10-per-pack discount at checkout — that's $50 off a 5-pack order and $100 off a 10-pack order — applied automatically when your cart hits the threshold.
Can I order different colors in one shipment and still get the bulk discount?
Yes. Each 10-pack ships as a single color (Galvanized, Black, or Green), but you can mix colors in the same cart. The bulk discount applies to the total number of 10-packs ordered, regardless of color combination. So 3 Galvanized + 2 Black still triggers the $10-per-pack discount on all five.
What roof pitches is the RORS01 rated for?
The Frontline RORS01 PitchFast Roof Anchor is certified for residential roofs with a pitch between 0/12 and 4/12 (low slope). It is not rated for use on pitches steeper than 4/12 and is not designed for standing seam metal roofs. For steeper residential or commercial roofs, contact us at 863-703-4522 to spec a different anchor.
What fasteners do I need to install the RORS01?
Twelve fasteners per anchor: either (12) 3.5" Grip-Rite exterior screws OR (12) 16D galvanized framing nails. A minimum of 8 must engage the structural wood truss; the remaining 4 fasteners may be anchored into the sheathing. Substrate must be a structural wood truss, minimum 3.5" thick. Fasteners are not included — they are sourced locally to fit your project.
Is the RORS01 reusable or single-use?
The RORS01 can be installed either temporarily or permanently. It is reusable when properly removed and inspected for deformation, corrosion, or damage. Many contractors leave them in place as permanent tie-off points for future maintenance, inspection, or service work after the roof is complete — that's the most cost-effective use over the life of the roof.
Does the RORS01 meet OSHA and ANSI requirements?
Yes. The Frontline RORS01 is certified to ANSI/ASSP Z359.18-2017 (U.S. anchorage connector standard) by Intertek (NRTL) under Report No. 105938082CRT-003, dated September 27, 2024. It meets the 5,000 lb minimum strength requirement of OSHA 1926.502(d)(15) for construction and OSHA 1910.140 for general industry. The full Intertek test report is available in the Submittal Documents section below.
Can I use the RORS01 on standing seam metal roofs?
No. The RORS01 is designed for residential wood-truss construction with low-slope (0/12 to 4/12) roof decking. For standing-seam metal roofs, use a non-penetrating, clamp-on anchor designed for that application — we recommend the SSRA1, which fits 95% of standing-seam profiles in the industry.
What are the most common installation mistakes with the RORS01?
Four things to watch for: (1) Wrong roof pitch — the anchor is rated for 0/12 to 4/12 only. Don't install on steeper roofs. (2) Fasteners not engaging the truss — at least 8 of the 12 fasteners must hit the structural wood truss, not just the sheathing. Use a stud finder if the truss isn't visible from above. (3) Wrong fastener type — only 3.5" Grip-Rite exterior screws or 16D galvanized framing nails are approved. Drywall screws, deck screws, or roofing nails will not hold the rated load. (4) Anchor not flush — if there's any gap between the base and the roof surface, the load path is compromised. All fasteners must be fully driven.
Frontline RORS01 Submittal Documents
The following manufacturer and third-party documents are available for download to support procurement, safety planning, jobsite submittals, and Competent Person inspection records. All documents apply directly to the Frontline RORS01 PitchFast Residential Roof Anchor.
| Document | Description | Download |
|---|---|---|
| Frontline RORS01 Spec Sheet | Frontline RORS01 specifications, dimensions, materials, design data, and installation requirements. | Frontline RORS01 — Spec Sheet (PDF) |
| Frontline RORS01 User Manual | Manufacturer's installation, inspection, and use instructions for the Frontline RORS01. | Frontline RORS01 — User Manual (PDF) |
| Frontline RORS01 Test Report | Intertek Test Report No. 105938082CRT-003 (Issued September 27, 2024) — ANSI/ASSP Z359.18-2017 certification by Intertek Testing Services NA Inc. | Frontline RORS01 — Intertek Test Report (PDF) |
Building a complete fall protection system for your residential job? Pair the RORS01 with a Frontline 110CTB harness, a self-retracting lanyard (SRL), or a shock-absorbing lanyard. Working on a steeper or commercial roof? Check out the GUS75 guardrail or CO2NN counterweight anchor for flat-roof applications. Not sure what works together? Call us — we spec complete systems before you buy.
Need help spec'ing anchors for a job? Call us — that's what we do. We help roofing contractors and framers spec complete fall protection systems before they buy. No upsell — just the right gear for the job.
863-703-4522
Frontline warrants its products against manufacturing defects in workmanship and materials, as well as product recalls, for a period of one (1) year from the date of purchase. This warranty excludes normal wear and tear, misuse, and improper installation. The limited warranty is provided only to an end-user customer for the period set forth in an order accepted by Fall Protection Distributors, LLC. The end user customer must be: (a) a Buyer purchasing product directly from Fall Protection Distributors, LLC or Buyer of product purchasing from an authorized reseller. The limited warranty covers defects in materials and workmanship in the Standing Seam Roof Anchor product. The limited warranty does not cover problems resulting from external causes such as accident, abuse, misuse, or problems with electrical power, servicing not authorized by Fall Protection Distributors, LLC, usage that is not in accordance with product instructions, failure to follow the product instructions or failure to perform preventive maintenance, problems caused by using accessories, parts, or components not supplied by Fall Protection Distributors, LLC; normal wear and tear; and products with missing or altered service tags or serial numbers. FALL PROTECTION DISTRIBUTORS, LLC’S RESPONSIBILITY FOR MALFUNCTIONS AND DEFECTS IN PRODUCT IS LIMITED TO REPAIR AND REPLACEMENT OF THE PRODUCT AS SET FORTH IN THIS WARRANTY STATEMENT. EXCEPT AS PROVIDED ABOVE, FALL PROTECTION DISTRIBUTORS, LLC AND ITS SUPPLIERS MAKE NO, AND HEREBY DISCLAIM ALL OTHER, WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
0 Reviews
Hide Reviews
Show Reviews
