New Hampshire Fall Protection Requirements

For information purposes only. This page supports your safety planning; it does not replace professional judgment. All safety plans and fall protection decisions must be reviewed and approved by a Competent Person or a Qualified Person, whichever OSHA requires, before work begins.
Federal OSHA state

New Hampshire Fall Protection Requirements

New Hampshire follows the federal OSHA baseline (no state plan for private employers).

The exact rules, in plain English, free

Ask All of Your Fall Protection
Questions Here

roofskylightguardrailanchoragewarning linesafety monitortrainingresidentialleading edgerescue
Ask a question, plain English is fine At what height does OSHA require fall protection in construction?Do I need fall protection on a residential roof?Is a skylight considered a hole?What does OSHA require for an anchor point?Is a warning line by itself enough on a flat roof?Do I have to tie off in a boom lift or scissor lift?Do I need written proof of fall protection training?How often do harnesses and lanyards have to be inspected?

New Hampshire fall protection at a glance

ItemDetail
Primary authorityFederal OSHA (U.S. Dept. of Labor)
Construction trigger height6 ft (29 CFR 1926.501)
General industry trigger4 ft (29 CFR 1910.28)
Report a serious incident1-800-321-6742

Who regulates fall protection in New Hampshire

ContactDetail
AgencyFederal OSHA (U.S. Dept. of Labor)
WebsiteOfficial site
Free consultationWorkWISE NH On-Site Consultation (Keene State College)

Report a serious injury or death

1-800-321-6742

Report a fatality within 8 hours, and an in-patient hospitalization, amputation, or loss of an eye within 24 hours. Call 911 first in an emergency.

Official page ›

New Hampshire requirements beyond the baseline

New Hampshire follows the federal OSHA baseline. New Hampshire follows the federal OSHA baseline (no state plan for private employers).

Equipment and anchorage requirements

Anchorages for personal fall arrest must support 5,000 pounds per attached worker or be engineered with a 2:1 safety factor under 29 CFR 1926.502(d)(15). Guardrails carry the 42 inch, 200 pound rules of 1926.502(b), and equipment is certified to ANSI Z359. Every anchor, harness, and SRL we sell publishes its tested strength on the spec sheet.

Penalties

Violation typeMaximum
Serious$16,550
Willful or Repeat$165,514

New Hampshire fall protection FAQ

Who enforces fall protection in New Hampshire?
Federal OSHA (U.S. Dept. of Labor). New Hampshire follows the federal OSHA baseline (no state plan for private employers).
At what height is fall protection required in New Hampshire?
For construction, 6 ft under 29 CFR 1926.501. For general industry, 4 ft under 29 CFR 1910.28.
What are the maximum penalties in New Hampshire?
Serious: $16,550; Willful or Repeat: $165,514. Confirm current amounts with the regulator.
How do I report a serious injury in New Hampshire?
Call 1-800-321-6742. Report a fatality within 8 hours, and an in-patient hospitalization, amputation, or loss of an eye within 24 hours. Call 911 first in an emergency.

Turn these rules into a printable, site-specific safety plan.

Generate My New Hampshire Safety Plan ›

Find the rule for your situation

Every duty in 1926.501, one tap each

Unprotected sides and edges

Any walking or working surface with an edge 6 ft or more above a lower level.

1926.501(b)(1)

Low-slope roofs

Roofing work on slopes 4:12 or less, including warning line and safety monitor combos.

1926.501(b)(10)

Steep roofs

Any roof steeper than 4:12. Guardrails with toeboards, nets, or personal fall arrest.

1926.501(b)(11)

Holes and skylights

Covers, guardrails, or fall arrest over every hole, including every skylight.

1926.501(b)(4)

Residential construction

The 6 ft rule for home building, and what a written fall protection plan requires.

1926.501(b)(13)

Leading edge work

Building the edge itself: decking, precast, and the controlled access zone rules.

1926.501(b)(2)

Personal fall arrest systems

Harnesses, lanyards, SRLs, 5,000 lb anchorages, free fall and clearance limits.

1926.502(d)

Guardrail systems

42 inch top rails, midrails, 200 lb strength, flagged lines, and gate rules.

1926.502(b)

Warning line systems

Line height, flag spacing, stanchion strength, and the 6 ft / 10 ft setbacks.

1926.502(f)

Safety monitoring systems

When a monitor alone is legal, and the five duties the monitor must perform.

1926.502(h)

Hole covers

Twice the expected load, secured against displacement, marked HOLE or COVER.

1926.502(i)

Training requirements

Who must be trained, by whom, the written certification record, and retraining.

1926.503

Hoist areas

Guardrails or fall arrest where materials come up over the edge.

1926.501(b)(3)

Excavations, wells, and pits

Guardrails, fences, barricades, or covers at the edge of excavations.

1926.501(b)(7)

Fall protection plans

The only legal alternative when conventional protection is infeasible.

1926.502(k)

The numbers worth quoting

Cite them anywhere, link this page as the source

15 years
1926.501 has been OSHA's most cited standard every fiscal year since 2011.
OSHA Top 10, FY2025
5,914
fall protection citations issued in FY2025, more than double any other standard.
OSHA Top 10, FY2025
370
construction and extraction workers killed by falls, slips, and trips in 2024.
BLS CFOI, 2024
6 ft
the height that triggers the fall protection duty on a construction site.
29 CFR 1926.501(b)(1)
5,000 lb
minimum anchorage strength per attached worker, unless engineered at 2:1.
29 CFR 1926.502(d)(15)
Citing this resource? Copy and paste: Fall Protection Regulation Hub, Fall Protection Distributors, LLC. Verbatim OSHA 29 CFR 1926 Subpart M via the eCFR, current through July 6, 2026. standingseamroofanchor.com

Know the rule? Now check your numbers.

Run the Fall Clearance Calculator

Fall protection regulation questions, answered

At what height does OSHA require fall protection in construction?
Six feet above a lower level, under 29 CFR 1926.501(b)(1). General industry workplaces trigger at 4 feet under 1910.28, shipyards at 5 feet, and longshoring at 8 feet. Two common construction exceptions: scaffolds trigger at 10 feet under Subpart L, and fixed ladders require protection when the climb reaches 24 feet. Working above dangerous equipment requires protection at any height.
Is there a rule that lets me skip fall protection if I stay 6 feet from the edge?
No. Federal OSHA has no safe-distance exemption for construction work. Six feet is the height that triggers the duty, not a buffer zone on the roof. The closest thing in the standard is the warning line system for low-slope roofing work under 1926.502(f), which must be rigged at least 6 feet from the edge (10 feet when mechanical equipment is in use) and only works in the specific combinations 1926.501(b)(10) allows.
Do I need fall protection on a residential roof?
Yes. Under 1926.501(b)(13), anyone doing residential construction 6 feet or more above a lower level needs guardrails, safety nets, or a personal fall arrest system. If the employer can demonstrate those are infeasible or create a greater hazard, the only alternative is a written, site-specific fall protection plan that meets every requirement of 1926.502(k), which includes a qualified person preparing it and a competent person supervising it.
What does OSHA require for an anchor point?
An anchorage for personal fall arrest must support at least 5,000 pounds per worker attached, or be designed, installed, and used under the supervision of a qualified person as part of a complete system that maintains a safety factor of at least two. That is 1926.502(d)(15). Anchorages must also be independent of any anchorage used to support or suspend platforms.
How high does a guardrail have to be?
The top rail must be 42 inches above the walking or working level, plus or minus 3 inches, and it must withstand 200 pounds of outward or downward force under 1926.502(b). Midrails go at 21 inches and must take 150 pounds. When guardrails protect a hole, they go on all unprotected sides, and any gate or removable section has its own rules in the same paragraph.
What is the difference between a competent person and a qualified person?
A competent person can identify existing and predictable hazards and has the employer's authority to promptly correct them, which includes stopping work. A qualified person has a degree, certificate, or extensive experience that lets them solve problems relating to the work, such as engineering an anchorage below 5,000 pounds. Subpart M assigns specific duties to each: for example, training under 1926.503 requires a competent person, and a fall protection plan under 1926.502(k) must be prepared by a qualified person.
Are the ANSI Z359 standards part of these regulations?
Not directly. OSHA regulations are federal law and free to read; ANSI Z359 is a voluntary consensus standard that manufacturers certify equipment against, and its text is copyrighted. OSHA can cite ANSI practices through the General Duty Clause, and most equipment you buy today, which includes everything we stock, is built to current Z359 requirements. Where an ANSI requirement matters to a product, we summarize it in plain language on the product page and in the manufacturer test reports we host.
Verified verbatim against the eCFR · current through July 6, 2026
About this text: the regulation paragraphs in the search tool above are reproduced verbatim from 29 CFR Part 1926 Subpart M as published in the Electronic Code of Federal Regulations, current through July 6, 2026. United States regulations are public domain. This page is an educational reference provided by Fall Protection Distributors, LLC and is not legal advice; always confirm requirements with the current CFR text and your state plan.
Data verified State authority page ready. Verified July 2026.. Volatile figures verified July 2026; confirm with the agency before relying on them. Rules change; confirm current requirements with the regulator before work begins. See every jurisdiction at our Fall Protection Regulation Hub.

!