4015-M Mechanical Rope Grab, 3-Pack
The Super Anchor 4015-M Integral Adjuster is a dual cam mechanical rope grab in zinc plated steel for SAS 5/8 inch synthetic lifelines. Squeeze the cam lock lever to slide the grab along the rope; release it and the grab holds position, then locks onto the lifeline in a single direction when subjected to the tension of a sudden force or free fall.
What is included: 3 Integral Adjuster 4015-M rope grabs. Each grab is a captive device with a 3,600 lb breaking strength and a maximum deceleration of 24 inches, connecting to the harness through a personal energy absorber or web lanyard with a class 1 connector. Compliant with OSHA 1926.502 and ANSI Z359.1-07.
Who Needs This Product
Crews that prefer an industry standard mechanical grab at a value price. The 4015-M is the workhorse grab supplied in SAS MAX bucket kits and factory attached lifeline assemblies: one hand squeezes the cam lever to reposition, and the dual cams do the holding, with no wraps to count. It is a captive grab, fed onto the lifeline at rigging time and not removed in the field, installed with the indicator arrow pointing to the lifeline anchor point. Connect it through an energy absorber or web lanyard to a full body harness as part of a complete personal fall arrest system. Not rated for reverse rigging or for X-Line 12-strand lifelines.
Features
Dual cam lock
Two cams drive onto the rope under load, locking the grab to the lifeline during a sudden force or free fall.
One-hand adjustment
Hold the cam lock lever down and slide the grab up or down the lifeline, then release to hold position.
Captive on the lifeline
The grab stays on the rope from rigging to takedown, so it cannot be dropped from the roof or left behind.
Factory attachment option
Supplied factory attached to SAS web lanyards and energy absorbers, or field connected with a class 1 connector.
Zinc plated steel
Plated body and cams resist corrosion; minor surface corrosion cleans up, deep pitting retires the grab.
Four-rivet body
Body rivets are inspection points; all four must be intact for the grab to stay in service.
Technical Specifications
| Model | 4015-M Integral Adjuster |
|---|---|
| Package | 3-pack |
| Type | Dual cam mechanical rope grab, captive |
| Material | Zinc plated (coated) steel |
| Breaking Strength | 3,600 lb (16 kN) |
| Locking | Single direction; indicator arrow points to lifeline anchor point |
| Maximum Deceleration | 24 inches, requires a personal energy absorber |
| Adjustment | Cam lock lever, one-hand operation |
| Lifeline Compatibility | SAS 5/8 inch synthetic lifelines; not for X-Line 12-strand |
| Attachment | Factory attached web lanyard or energy absorber, or class 1 connector |
| Reverse Rigging | Not rated |
| Compliance | OSHA 1926.502; ANSI Z359.1-07 |
Install with the direction arrow pointing to the lifeline anchorage end. A rope grab installed backwards will not lock in a fall, resulting in serious injury or death. Do not attach the 4015-M directly to the harness dorsal or side D-ring, do not use it for reverse rigging or on X-Line lifelines, and do not apply lubricants.
Compliance Standards
OSHA 1926.502
Meets federal construction fall protection criteria for personal fall arrest system components.
ANSI Z359.1-07
Integral adjuster rope grab complies with the ANSI fall protection code per the SAS rope grab manual.
CSA Z259.11-05
Referenced lifeline compatibility standard in the SAS 12-strand lifeline manual for integral adjuster pairings.
ANSI Z359.12 Connectors
Field connections use class 1 snaphooks or carabiners with 3,600 lb gate strength.
Typical Applications
Installation Overview
Full figures and function tests are in the Rope Grabs manual and SAS Lifeline Manual 05-2024 linked below. The basics:
- Feed the lifeline through the grab at rigging time with the indicator arrow pointing to the lifeline anchor point.
- Attach the lifeline A-end to an OSHA or ANSI compliant anchorage device with a class 1 connector.
- Connect the grab connector ring to a personal energy absorber or SAS web lanyard, then to the harness dorsal D-ring.
- Tie a limiter knot below the working position on the lifeline to gauge free fall length and protect the rope end.
- Hold the cam lock lever down to slide the grab to the working position, then release the lever.
- Perform the cam lock test and the spring and mobility tests before each use; any failure removes the grab from service.
Inspection and Retirement
Inspect before installation and each use, with documented annual inspections. Remove the equipment from service when any of the following apply:
- Any of the 4 body rivets are missing or loose.
- The cam lock lever does not spring back quickly when released.
- The grab moves on the lifeline during the cam lock test, or will not move easily during the mobility test.
- The connector ring is bent or deformed.
- Deep pitting or extreme rust is present on the zinc plating.
- The grab was subjected to a free fall.
Tag equipment removed from service to prevent further use until inspected by a qualified or competent person.
Fall ProtectionDistributors, LLC Free Tool · No Signup · OSHA 1926.502 Free Interactive Tool Fall Protection Calculator Pick your system. Run the math. Generate a plan. 1Pick Your SystemDetermine fall restraint vs. fall arrest based on your work surface, edge access, and clearance. 2Run the MathCalculate exact fall clearance required below the work surface for your SRL or lanyard setup. 3Generate a PlanGet a printable OSHA-compliant Fall Protection Plan structured around 29 CFR 1926.502(k).
Frequently Asked Questions
Super Anchor 4015-M Submittals and Documentation
Rope Grabs Instruction/Specification Manual (PDF)Rope grab types, performance specifications, function tests, and inspection requirements for SAS 5/8 inch lifelines. SAS Synthetic Lifelines Manual 05-2024 (PDF)Lifeline model specifications, rope grab compatibility, limiter knot requirements, lock tests, and length of fall calculations. Lifelines Compatibility with Rope Grabs (PDF)Standard and reverse rigging diagrams, lifeline material specifications, and rope grab pairing table. Super Anchor Warranty and Compliance Statement (PDF)Manufacturer warranty terms and compliance statement for Super Anchor Safety products.Compatible and Related Products
- Super Anchor 4020 3-Strand Value Lifeline. 5/8 inch lifeline for the 4015-M in 25 to 100 ft lengths.
- Super Anchor 4015-Z Fall Arresters. Removable mechanical grab with anti-panic function.
- Super Anchor SuperGrab 4015 Rope Grabs. Prussic grab rated for reverse rigging and X-Lines.
- Super Anchor 6101GH Deluxe Harness. Full body harness for the lifeline and rope grab system.
Restocking Rope Grabs for the Season?
Tell us how many lifelines you run and we will match 4015-M packs with absorbers, lanyards, and replacement lifelines in one order with accurate freight, based on the delivery location.
Call 863-703-4522 to talk to a fall protection specialist.
Super Anchor Safety Manufacturer Warranty
Super Anchor Safety (SAS) warrants to the purchaser that all products are free from defect in material and workmanship at the time of shipment. This warranty is limited to product replacement for a period of one (1) year from the date of installation or use by the owner, provided that this period shall not exceed two (2) years from the date of shipment. This warranty only covers defects in material and workmanship. It does not cover conditions resulting from normal wear, neglect, abuse, or accident. This product warranty does not cover oxidation of zinc, dacromet, or powder coatings used on permanent and temporary anchors that results from connector abrasion unless the coating can be shown to be defective at the time of purchase. This warranty is non-transferable. Any unused defective product will be replaced at no charge by returning the product to Super Anchor Safety or to the distributor the product was purchased from.
Permanent Anchor Warranty
Super Anchor Safety warrants to the purchaser that all anchors sold as a permanent fixture with Hot Dip Galvanizing, Stainless Steel, and Thermo-Plastic finishes are fully warranted against failure due to defects in materials or workmanship for a period of five (5) years from the date of initial installation. SAS does not warranty the installation or flashing system used to waterproof the anchors. The SAS factory warranty is void if the product has been modified or has not been used in accordance with SAS specifications and instructions for that product. Anchors that have been removed from service due to re-roofing or remodel of the structure they were originally attached to must be inspected by an SAS factory representative or a competent person before being reinstalled.
See the Super Anchor Warranty and Compliance Statement (PDF) for the full manufacturer document.
