ACQW12 ToolGrip Quick Wrap Anchoring Tool Tape, 12 ft, 4-Pack
Most hand tools have nowhere to clip a tether - the Frontline ACQW12 fixes that. Wrap the self-adhesive tape around the tool body to create a strong, durable tether attachment point with anchor in seconds, on essentially any tool, while adding extra grip to the handle.
The roll runs 12 ft long by 1.7 in wide and builds attachment points rated for tools up to 5 lbs, conforming to ANSI/ISEA 121-2018 for dropped object prevention.
Who Needs This Product
This product is dropped-object prevention equipment from the Frontline ToolGrip line. Crews working at height tether their tools so a slip never becomes a struck-by incident below. ToolGrip products are rated for tools only - personal fall protection is a separate system.
Features
Anchor point in seconds
Wrap the tape, cinch the anchor loop, clip the tether - done.
Works on almost anything
Wrenches, pliers, screwdrivers, levels - if you can wrap it, you can tether it.
Adds grip
The wrap doubles as a tackier, more comfortable handle surface.
5 lb rating
Sized for the hand tools that cause most dropped-object incidents.
12 ft per roll
Outfit a whole tool bag from a single roll.
Pairs with any ToolGrip tether
Use with the TLS15, TLS30, or TLC05 tethers to complete the connection.
Technical Specifications
| SKU | ACQW12 |
|---|---|
| Type | Quick wrap anchoring tool tape |
| Roll length | 12 ft |
| Width | 1.7 in |
| Bond strength | 5 lbs |
| Installation | Self-adhesive wrap |
| Standards | ANSI/ISEA 121-2018 |
Tool tethering equipment only - NEVER personal fall protection. ToolGrip products are rated for tools, in the capacities on the spec sheet. Never connect any ToolGrip component to a personal fall arrest or restraint system, and never exceed the rated tool weight.
Compliance Standards
ANSI/ISEA 121-2018
American National Standard for dropped object prevention solutions - the consensus standard for tool tethering equipment.
OSHA 1926.759
Falling object protection requirements in steel erection; tethering supports compliance.
OSHA General Duty Clause
Dropped-tool struck-by incidents are routinely cited under 5(a)(1); tethering is the recognized control.
Typical Applications
How to Build an Attachment Point with ACQW12
Follow the manufacturer's manual. The sequence below is an overview only.
- Clean the tool. Wipe the wrap area free of oil and dust.
- Position the anchor loop. Lay the tether loop against the tool body where the wrap will capture it.
- Wrap. Apply the self-adhesive tape in tight, overlapping turns per the manual.
- Set the bond. Press the finished wrap firmly and let it set before loading.
- Clip and verify. Connect the tether and tug-test before working at height.
Inspection and Retirement
Inspect before each use. Pull the equipment from service for any of the conditions below.
- Webbing and elastic: cuts, fraying, abrasion, burns, or loss of elasticity.
- Stitching: broken, pulled, or abraded threads.
- Hardware: deformation, cracks, corrosion, or gates and locks that fail to close.
- Attachment points: loose tape bonds, worn loops, or damaged D-rings.
- Markings: labels must be present and legible.
Remove from service immediately if any inspection point fails or after the tether arrests a dropped tool with visible damage. ToolGrip products are tool tethering equipment - never use them for personal fall protection.
Frequently Asked Questions
Frontline ACQW12 Submittals and Documentation
Frontline ACQW12 Spec Sheet (PDF)Roll length, width, bond strength, and standards. Frontline ToolGrip User Manual (PDF)Use, limitations, inspection, and retirement for the ToolGrip tool tethering line. Frontline ToolGrip Quick Display Guide (PDF)Line overview of the ToolGrip tool tethering family. Frontline Catalog (PDF)The full Frontline Fall Protection product catalog.Compatible and Related Products
- Frontline TLS15 Elastic Tool Tether. The everyday 15 lb tether to clip to your new anchor points.
- Frontline TLC05 Coil Tool Tether. A close-body coil tether for 5 lb hand tools.
- Frontline ACTLDR Tool D-Ring Anchor. A webbing D-ring anchor for belts and harnesses.
Building a Dropped-Object Program?
Tethers, anchors, holsters, and pouches work as a system. Confirm your tool list and working heights with us and we will walk through the ToolGrip lineup so the right equipment ships together.
Call 863-703-4522 to talk to a fall protection specialist.
