ACTLS222C ToolGrip 22 lbs Tool Lanyard Cinch with D-Ring, 8-Pack
The Frontline ACTLS222C handles the tools that have nowhere to clip: its large loop chokes directly around the tool body to make the connection, while a steel D-ring connects the other end to the user's harness or a tool-holding hook on the belt.
The elasticated polyester webbing contracts to 2.79 ft at rest, extends to 4.43 ft in use, and carries a 22 lb strength rating with a high strength aluminum carabiner - all at 0.2 lbs. ANSI/ISEA 121-2018 dropped object prevention.
Who Needs This Product
This product is dropped-object prevention equipment from the Frontline ToolGrip line. Crews working at height tether their tools so a slip never becomes a struck-by incident below. ToolGrip products are rated for tools only - personal fall protection is a separate system.
Features
Chokes any tool
The large loop cinches around tool bodies with no native attachment point.
22 lb strength
Headroom for heavier hand tools.
Steel D-ring end
Connects to the harness or a tool-holding hook on the belt.
Elastic contraction
Stays short at rest, stretches when you reach.
Featherweight
0.2 lbs total.
No tape needed
For tools the cinch can capture, skip the wrap entirely.
Technical Specifications
| SKU | ACTLS222C |
|---|---|
| Type | Single-leg elasticated cinch tool lanyard |
| Strength | 22 lbs |
| Connection, tool end | Large cinch/choke loop |
| Connection, user end | Steel D-ring / steel ring for tool-holding hook |
| Relaxed length | 2.79 ft |
| Expanded length | 4.43 ft |
| Webbing | Polyester, elasticated |
| Carabiner | High strength aluminum |
| Weight | 0.2 lbs |
| Standards | ANSI/ISEA 121-2018 |
Tool tethering equipment only - NEVER personal fall protection. ToolGrip products are rated for tools, in the capacities on the spec sheet. Never connect any ToolGrip component to a personal fall arrest or restraint system, and never exceed the rated tool weight.
Compliance Standards
ANSI/ISEA 121-2018
American National Standard for dropped object prevention solutions - the consensus standard for tool tethering equipment.
OSHA 1926.759
Falling object protection requirements in steel erection; tethering supports compliance.
OSHA General Duty Clause
Dropped-tool struck-by incidents are routinely cited under 5(a)(1); tethering is the recognized control.
Typical Applications
How to Use the ACTLS222C
Follow the manufacturer's manual. The sequence below is an overview only.
- Inspect. Check webbing, loop, stitching, D-ring, and carabiner before each use.
- Choke the tool. Pass the large loop around the tool body and back through itself, cinched snug.
- Connect the user end. Attach the steel D-ring to the harness or the ring to a tool-holding hook.
- Set the cinch. Confirm the choke cannot slide off the tool taper.
- Tug test. Verify before working at height.
Inspection and Retirement
Inspect before each use. Pull the equipment from service for any of the conditions below.
- Webbing and elastic: cuts, fraying, abrasion, burns, or loss of elasticity.
- Stitching: broken, pulled, or abraded threads.
- Hardware: deformation, cracks, corrosion, or gates and locks that fail to close.
- Attachment points: loose tape bonds, worn loops, or damaged D-rings.
- Markings: labels must be present and legible.
Remove from service immediately if any inspection point fails or after the tether arrests a dropped tool with visible damage. ToolGrip products are tool tethering equipment - never use them for personal fall protection.
Frequently Asked Questions
Frontline ACTLS222C Submittals and Documentation
Frontline ACTLS222C Spec Sheet (PDF)Lengths, strength, materials, and standards. Frontline ToolGrip User Manual (PDF)Use, limitations, inspection, and retirement for the ToolGrip tool tethering line. Frontline ACTLS22 Test Report (PDF)Third-party test report for the ToolGrip tool tether family (model designation ACTLS22). Frontline ToolGrip Quick Display Guide (PDF)Line overview of the ToolGrip tool tethering family. Frontline Catalog (PDF)The full Frontline Fall Protection product catalog.Compatible and Related Products
- Frontline ACTLS222 11 lb Twin Tool Lanyard. The two-tool Y-leg version.
- Frontline ACQW12 Quick Wrap Tool Tape. For tools the cinch cannot capture.
- Frontline ACTLDR Tool D-Ring Anchor. A dedicated belt anchor point.
Building a Dropped-Object Program?
Tethers, anchors, holsters, and pouches work as a system. Confirm your tool list and working heights with us and we will walk through the ToolGrip lineup so the right equipment ships together.
Call 863-703-4522 to talk to a fall protection specialist.
