Concrete and Steel D-Ring Reusable Anchor Plate
The Frontline COP01 is a bolt-on anchorage connector plate for concrete and steel structures. The 6 in x 6 in ASTM rated steel plate carries a welded D-ring and four pre-drilled mounting holes, and every concrete anchor bolt needed for installation comes in the bag, ready to use. Bolt it to a wall, ceiling, column, or steel member, tie off to the D-ring, and you have a 5,000 lbf rated anchor point exactly where the work is.
The plate installs in horizontal or vertical orientations and works as either a temporary anchor that moves with the crew or a permanent tie-off point that stays with the structure. Powder-coated safety green so it reads as fall protection at a glance. Rated for one user at 130-310 lbs. The spec sheet claims ANSI Z359.18 and A10.32 plus OSHA 1926 and 1910. Sold as a 2-pack — two concrete anchor plates for $149, shipped together in one order.
Who Needs This Product
This product is a bolt-on anchorage connector plate. It provides the anchor-side tie-off point of a personal fall arrest or fall restraint system on concrete or steel structures. Pair it with a full body harness and an energy-absorbing lanyard or self-retracting lifeline. It is not a complete fall protection system on its own, and a competent person must verify the supporting structure before use.
Features
Bolt-on D-ring anchorage
A welded D-ring on a 6 in x 6 in plate puts a rated tie-off point on walls, ceilings, columns, and steel members.
Hardware included
Four pre-drilled holes and all concrete anchor bolts come in the bag, ready to install straight away.
Concrete or steel
One plate covers both substrates, so the same anchor standard works across the whole structure.
Temporary or permanent
Use it as a relocatable crew anchor or leave it installed as a permanent tie-off point.
ASTM rated steel
Plate stock is ASTM rated steel, powder-coated safety green for visibility and corrosion protection.
Horizontal or vertical mounting
Installs and works in horizontal or vertical applications per the user manual.
Technical Specifications
| Model | COP01 |
|---|---|
| Tensile strength | 5,000 lbf / 22 kN |
| User capacity | 130-310 lbs, single user |
| Material | ASTM rated steel, powder-coated safety green |
| Plate dimensions | 6 in x 6 in |
| Mounting | 4 pre-drilled holes; concrete anchor bolts included |
| Substrates | Concrete or steel |
| Service | Temporary or permanent |
| Shipping weight | Approx. 5 lbs |
| Sold As | 2-Pack (2 per order) |
The structure is the anchor. The plate is only as strong as what it is bolted to. A competent person must verify that the concrete or steel substrate, the fasteners, and the installation meet the requirements in the Frontline user manual before anyone ties off. Follow the manual's hole pattern, fastener, and torque requirements exactly.
Compliance Standards
ANSI Z359.18
American National Standards Institute standard for anchorage connectors used in active fall protection systems, as claimed on the Frontline spec sheet.
ANSI A10.32
Fall protection systems requirements for construction and demolition operations.
OSHA 1926
Federal OSHA construction industry fall protection regulations.
OSHA 1910
Federal OSHA general industry walking-working surfaces and fall protection regulations.
Typical Applications
Installation Overview
Follow the manufacturer's manual. The sequence below is an overview only.
- Select. Have a competent person choose sound structural concrete or steel that meets the manual's substrate requirements.
- Position. Place the plate where the tie-off keeps the lifeline aligned with the work and mark the four hole locations.
- Drill. Drill the four holes to the diameter and depth the manual specifies for the included anchor bolts.
- Fasten. Clean the holes, install all four supplied concrete anchor bolts, and torque per the manual.
- Verify. Confirm the plate sits flush, all fasteners are tight, and the D-ring is sound before connecting a system.
Inspection and Retirement
Inspect before each use, with a documented competent-person inspection at least every 6 months. Pull the equipment from service for any of the conditions below.
- Bent, cracked, or deformed plate or D-ring
- Loose, missing, damaged, or corroded mounting bolts
- Cracked or chipped powder coating with rust on the base steel
- Cracked, spalled, or deteriorated concrete around the fasteners
- Missing or illegible product labels and markings
- Any evidence the plate has arrested a fall
Remove the plate from service immediately if it has been subjected to fall arrest forces or fails any inspection point, and destroy retired equipment so it cannot be returned to use.
Fall ProtectionDistributors, LLC Free Tool · No Signup · OSHA 1926.502 Free Interactive Tool Fall Protection Calculator Pick your system. Run the math. Generate a plan. 1Pick Your SystemDetermine fall restraint vs. fall arrest based on your work surface, edge access, and clearance. 2Run the MathCalculate exact fall clearance required below the work surface for your SRL or lanyard setup. 3Generate a PlanGet a printable OSHA-compliant Fall Protection Plan structured around 29 CFR 1926.502(k).
Frequently Asked Questions
Frontline COP01 Submittals and Documentation
Frontline COP01 Spec Sheet (PDF)Ratings, dimensions, materials, and the compliance summary straight from Frontline. Frontline COP01 User Instruction Manual (PDF)Installation, use, and inspection instructions for the COP01 anchor plate. Frontline COP01 Test Report (PDF)Independent laboratory test results for the COP01 anchor plate.Compatible and Related Products
- Frontline COP02-10K Anchor Plate. The 10,000 lb hot dip galvanized plate for higher rated anchorage requirements.
- Frontline COP02-10K-CAL Anchor Plate. The Cal-OSHA version with a 130-420 lb user capacity for California jobsites.
- Frontline COT345K Reusable Toggle Bolt Anchor. A reusable toggle bolt anchor for hollow-core concrete and steel flange tie-offs.
Put a Rated Tie-Off Point Exactly Where You Need It
Need help specifying the right system for your jobsite? Confirm your application, anchorage, and clearance with us and we will walk through the kit list so the right equipment ships together.
Call 863-703-4522 to talk to a fall protection specialist.
