Name: Super Anchor Super Bolt Reusable Concrete Temporary Anchor
Brand: Super Anchor
SKU: 1040
Price: 226.8 USD
Availability: InStock

Description
Warranty Information
Reviews

Super Anchor Temporary Anchors

Super Anchor Super Bolt Reusable Concrete Temporary Anchor

The Super Anchor Super Bolt is a reusable concrete anchorage device that inserts into a concrete structure for a temporary tie-off. Drill a 3/4 inch hole into the concrete, clean it, and insert the Super Bolt. It installs in seconds and can be used on horizontal, vertical, and overhead surfaces.

The Super Bolt is a single point anchorage connector for personal fall arrest, rated for one worker. It is made of stainless steel with a minimum breaking strength of 5,000 pounds and meets ANSI Z359.18 Type A. It is reusable, so it moves from hole to hole across the job.

Super Anchor Super Bolt reusable concrete temporary anchor, stainless steel single point anchorage

5,000 lbMin Breaking Strength

1,800 lbMax Arrest Force

310 lbMax User Weight

3/4 inDrilled Hole

StainlessSteel Build

Type AANSI Z359.18

ReusableMoves Hole to Hole

TemporaryConcrete Anchor

Who Needs This Product

The Super Bolt is a temporary concrete anchor for workers who need a fast, reusable single point tie-off in concrete. It suits horizontal, vertical, and overhead concrete surfaces on construction and service work. Complete the system with a full-body harness and an energy-absorbing connecting device.

Features

Installs in seconds

Drill a 3/4 inch hole, clean it, and insert the Super Bolt for an immediate anchor.

Horizontal, vertical, overhead

Works in concrete on any orientation of surface.

Reusable

Moves from hole to hole across the job, so one anchor covers many tie-off points.

Stainless steel

Corrosion resistant construction rated to a 5,000 lb minimum breaking strength.

Single point anchorage

A dedicated single worker fall arrest anchorage connector.

ANSI Z359.18 Type A

Meets the American National Standard for anchorage connectors, Type A.

⚠

This is a single user temporary anchor, not a complete system. The concrete must be sound and rated for the load, verified by a competent person. Use a full-body harness with an energy-absorbing connecting device and confirm fall clearance. Run the Fall Protection Calculator below before you tie off.

Compliance Standards

ANSI Z359.18 Type A

American National Standard for anchorage connectors, Type A.

OSHA 29 CFR 1926.502

Federal construction fall protection anchorage requirements.

Typical Applications

Concrete constructionTemporary tie-off in poured concrete.

Precast and tilt-upAnchor point on concrete panels.

Overhead concreteFall arrest on overhead concrete surfaces.

MaintenanceReusable anchor for concrete service work.

How to Install the Super Bolt

Follow the Super Anchor Safety instruction manual. The sequence below is an overview only.

Confirm the concrete. Verify the concrete is sound and rated for the load per a competent person.
Drill the hole. Drill a 3/4 inch hole to the depth given in the instruction manual.
Clean the hole. Clear dust and debris so the anchor seats fully.
Insert the Super Bolt. Set the anchor into the hole until it is fully seated.
Verify. Connect your harness and energy-absorbing device and confirm fall clearance.

Inspection and Retirement

Inspect before each use, with a documented competent-person inspection at least annually. Remove the product from service for any condition below.

Anchor body: cracks, deformation, corrosion, or elongated holes.
Coating: worn or damaged galvanizing, dacromet, or powder coat at the connection point.
Fasteners and flashing: loose, missing, backed-out, or leaking hardware.
D-ring or connection point: burrs, sharp edges, or excessive wear.
Labels: illegible or missing product identification.

Retire the anchor immediately after any fall-arrest event, or if any inspection point fails.

Fall Protection
Distributors, LLC Free Tool · No Signup · OSHA 1926.502 Free Interactive Tool Fall Protection Calculator Pick your system. Run the math. Generate a plan. 1Pick Your SystemDetermine fall restraint vs. fall arrest based on your work surface, edge access, and clearance. 2Run the MathCalculate exact fall clearance required below the work surface for your setup. 3Generate a PlanGet a printable OSHA-compliant Fall Protection Plan structured around 29 CFR 1926.502(k). Run the Numbers and Stay Safe Launch the Calculator ›

Technical Specifications

SKU	1040
Manufacturer Part Number	1040
Type	Reusable concrete single point anchorage
Material	Stainless steel
Installed in	3/4 in drilled hole
Capacity	1 worker
Min breaking strength	5,000 lbf (22 kN)
Max arrest force	1,800 lb
Max user weight	310 lb including clothing, tools, and equipment
Surfaces	Horizontal, vertical, and overhead concrete
Standards	ANSI Z359.18 Type A; OSHA 1926.502
Warranty	Super Anchor Safety manufacturer warranty; see Warranty tab

Frequently Asked Questions

How does the Super Bolt install?

Drill a 3/4 inch hole into sound concrete, clean it, and insert the anchor. It installs in seconds. Verify that the mounting surface is sound and that every fastener is fully seated before the anchor is put into service. Always inspect the product before each use and take it out of service if you notice any damage, deformation, or excessive wear.

Can I reuse it?

Yes. The Super Bolt is reusable and moves from hole to hole across the job. Never modify or repair the product in the field, since altering it can compromise its ability to arrest a fall. If you have any doubt about the correct setup, consult a qualified person or the manufacturer instructions before putting the system into service.

What surfaces can I use it on?

Horizontal, vertical, and overhead concrete surfaces. Confirm the surface, slope, and conditions at your work area match the intended application before installation. If you have any doubt about the correct setup, consult a qualified person or the manufacturer instructions before putting the system into service.

How many workers can use it?

One worker. It is a single point anchorage connector for personal fall arrest. Pair it only with connectors and equipment that are approved for use together so the complete system performs as designed. Keep the manufacturer instructions with the equipment so anyone using it can reference the approved procedures.

What is it made of?

Stainless steel, with a minimum breaking strength of 5,000 pounds. See the Technical Specifications on this page for the exact materials, dimensions, and ratings. Before every use, confirm the product is compatible with the rest of your fall protection system and that you have adequate fall clearance below the work area.

What standard does it meet?

ANSI Z359.18 Type A, aligning with OSHA 1926.502. Using the product within the limits described on this page helps keep your setup consistent with recognized fall protection practice. A qualified person should verify that the installation and the overall system meet the requirements of your specific job site.

Do I need a harness with this anchor?

Yes. The anchor is an anchorage point only and must be paired with a full-body harness and an energy-absorbing connecting device. Make sure the connecting hardware and anchorage suit your application before you attach a lanyard or lifeline. Before every use, confirm the product is compatible with the rest of your fall protection system and that you have adequate fall clearance below the work area.

Super Anchor Super Bolt Concrete Anchor Submittals and Documentation

Super Bolt Pocket Manual (PDF)Use, installation, capacity, and inspection. Warranty and Compliance Statement (PDF)Manufacturer warranty and standards compliance.

Related Super Anchor Products

Tying Off to Concrete?

Concrete condition, hole depth, and the connecting device all affect a safe anchor. Confirm your surface with us and we will help match the Super Bolt with the right harness and lanyard.

Call 863-703-4522 to talk to a fall protection specialist.

Super Anchor Safety Manufacturer Warranty

Super Anchor Safety (SAS) warrants to the purchaser that all products are free from defect in material and workmanship at the time of shipment. This warranty is limited to product replacement for a period of one (1) year from the date of installation or use by the owner, provided that this period shall not exceed two (2) years from the date of shipment. This warranty only covers defects in material and workmanship. It does not cover conditions resulting from normal wear, neglect, abuse, or accident. This product warranty does not cover oxidation of zinc, dacromet, or powder coatings used on permanent and temporary anchors that results from connector abrasion unless the coating can be shown to be defective at the time of purchase. This warranty is non-transferable. Any unused defective product will be replaced at no charge by returning the product to Super Anchor Safety or to the distributor the product was purchased from.

Permanent Anchor Warranty

Super Anchor Safety warrants to the purchaser that all anchors sold as a permanent fixture with Hot Dip Galvanizing, Stainless Steel, and Thermo-Plastic finishes are fully warranted against failure due to defects in materials or workmanship for a period of five (5) years from the date of initial installation. SAS does not warranty the installation or flashing system used to waterproof the anchors. The SAS factory warranty is void if the product has been modified or has not been used in accordance with SAS specifications and instructions for that product. Anchors that have been removed from service due to re-roofing or remodel of the structure they were originally attached to must be inspected by an SAS factory representative or a competent person before being reinstalled.

See the Super Anchor Warranty and Compliance Statement (PDF) for the full manufacturer document.

0 Reviews Hide Reviews Show Reviews