Name: Super Anchor Retro-Flash Flashing 80-Pack, 2401-B
Brand: Super Anchor
SKU: 2401-B
Price: 648 USD
Availability: InStock

Description
Warranty Information
Reviews

Super Anchor Roof Anchor Flashing

Super Anchor Retro-Flash Flashing 80-Pack, 2401-B

Retro-Flash is sold in contractor volume packs. Choose the 10-pack or 80-pack at checkout.

14 x 4 inFlashing Plate

20 gaSteel

Dacromet CoatedZinc Plated

WatertightRetro-Fit

D-Minus / RSCompatible

10 or 80 PackVolume

Corrosion ResistantFinish

Roof FlashingAccessory

Who Needs This Product

Retro-Flash is a flashing accessory for roofers and building owners installing D-Minus or RS series anchors on an existing roof who need a watertight seal. It is a flashing component, not a fall-arrest anchor by itself.

Features

20 gauge steel plate

Durable 14 by 4 inch flashing plate.

Dacromet coated zinc plated

Corrosion resistant finish for long roof life.

Watertight retro-fit

Flashes the anchor watertight on a roof already installed.

Fits D-Minus and RS anchors

Sized for Super Anchor D-Minus and RS series anchors.

Slides under the shingle course

Sheds water over the anchor penetration.

Contractor volume packs

Sold in 10-pack and 80-pack quantities.

⚠

This is one component of a personal fall-arrest system. Retro-Flash is a flashing component. It does not replace the roof anchor and must be installed per the anchor instructions for a watertight seal. Inspect before each use and confirm compatibility, capacity, and fall clearance. Run the Fall Protection Calculator below before you tie off.

Compliance Standards

ANSI Z359

American National Standard for fall protection equipment.

OSHA 29 CFR 1926.502

Federal construction fall protection requirements.

Typical Applications

Re-roofingWatertight anchor flashing.

RoofingRetro-fit flashing.

Building ownersSeal existing anchor penetrations.

ContractorsVolume flashing supply.

How to Use the Retro-Flash Flashing

Follow the Super Anchor Safety instruction manual. The sequence below is an overview only.

Inspect. Check for wear, cuts, distortion, corrosion, and gate or hardware function before each use.
Confirm compatibility. Verify the component, harness, and anchor are compatible and rated.
Connect. Make the connection and confirm every gate is fully closed and locked.
Verify. Confirm the full system, capacity, and fall clearance.
Use. Work within the rated limits of the system.

Inspection and Retirement

Inspect before each use, with a documented competent-person inspection at least annually. Remove the product from service for any condition below.

Webbing or body: cuts, frays, abrasion, burns, corrosion, or distortion.
Stitching: pulled, cut, or broken threads.
Gates and locks: proper close and lock function.
Fall indicators: any sign of deployment.
Labels: illegible or missing markings.

Retire the anchor immediately after any fall-arrest event, or if any inspection point fails.

Fall Protection
Distributors, LLC Free Tool · No Signup · OSHA 1926.502 Free Interactive Tool Fall Protection Calculator Pick your system. Run the math. Generate a plan. 1Pick Your SystemDetermine fall restraint vs. fall arrest based on your work surface, edge access, and clearance. 2Run the MathCalculate exact fall clearance required below the work surface for your setup. 3Generate a PlanGet a printable OSHA-compliant Fall Protection Plan structured around 29 CFR 1926.502(k). Run the Numbers and Stay Safe Launch the Calculator ›

Technical Specifications

SKU	2401-B (80 flashings)
Type	Retro-Flash flashing plate
Size	14 x 4 in
Material	20 ga Dacromet coated zinc plated steel
Fits	D-Minus and RS series anchors
Use	Flashing accessory
Warranty	Super Anchor Safety manufacturer warranty; see Warranty tab

Frequently Asked Questions

What is the 2401-B?

The Super Anchor 2401-B is the contractor 80-pack of Retro-Flash flashing plates: 20 gauge Dacromet coated zinc plated steel, 14 by 4 inches, for flashing D-Minus and RS series roof anchors watertight across full projects. Only trained workers should select, install, and use fall protection equipment for its intended application. A qualified person should verify that the installation and the overall system meet the requirements of your specific job site.

For the 2401-B, what size is the plate?

14 by 4 inches, 20 gauge steel. Refer to the specification table above for full details on construction, finish, and sizing. For complete protection, pair it with a compatible full body harness, connector, and shock absorbing lanyard or self retracting lifeline. Before every use, confirm the product is compatible with the rest of your fall protection system and that you have adequate fall clearance below the work area.

For the 2401-B, what is the finish?

Dacromet coated zinc plated steel for corrosion resistance. Refer to the specification table above for full details on construction, finish, and sizing. Store it in a clean, dry place away from heat and chemicals to help preserve its condition between uses. Store it in a clean, dry place away from heat and chemicals to help preserve its condition between uses.

Why choose the 2401-B configuration?

The 80-pack is the production volume: one box flashes anchors across an entire subdivision phase without reordering. Always inspect the product before each use and take it out of service if you notice any damage, deformation, or excessive wear. Before every use, confirm the product is compatible with the rest of your fall protection system and that you have adequate fall clearance below the work area.

For the 2401-B, how does it seal?

It slides under the shingle course above the anchor to shed water over the penetration. Check that the location and environment are appropriate for this product before putting it to work. Only trained workers should select, install, and use fall protection equipment for its intended application.

For the 2401-B, what pack sizes are available?

A 10-pack and an 80-pack. The specifications listed on this page outline the build details you need for your application. Only trained workers should select, install, and use fall protection equipment for its intended application. Always inspect the product before each use and take it out of service if you notice any damage, deformation, or excessive wear.

What completes a system with the 2401-B?

No. It is a flashing accessory used with a Super Anchor roof anchor. Confirm the surface, slope, and conditions at your work area match the intended application before installation. Keep the manufacturer instructions with the equipment so anyone using it can reference the approved procedures.

Retro-Flash Flashing Submittals and Documentation

Spiral Shank Nail Spec (PDF)Stainless fastener specifications for anchor installation. Retro Flashing Guide (PDF)Flashing installation guide for retro-fit anchors. Retro-Flash Flyer (PDF)Retro-Flash system overview and applications. Retro-Flash 2401-S Flyer (PDF)2401-S flashing details and installation. RS-10 D-Minus Flyer (PDF)RS-10 and D-Minus anchor family overview. Super Anchor Warranty and Compliance Statement (PDF)Manufacturer warranty and standards compliance.

Related Super Anchor Products

Buying Retro-Flash in Volume?

Anchor type and quantity affect the order. Confirm your project with us and we will help you order the right flashing.

Call 863-703-4522 to talk to a fall protection specialist.

Super Anchor Safety Manufacturer Warranty

Super Anchor Safety (SAS) warrants to the purchaser that all products are free from defect in material and workmanship at the time of shipment. This warranty is limited to product replacement for a period of one (1) year from the date of installation or use by the owner, provided that this period shall not exceed two (2) years from the date of shipment. This warranty only covers defects in material and workmanship. It does not cover conditions resulting from normal wear, neglect, abuse, or accident. This product warranty does not cover oxidation of zinc, dacromet, or powder coatings used on permanent and temporary anchors that results from connector abrasion unless the coating can be shown to be defective at the time of purchase. This warranty is non-transferable. Any unused defective product will be replaced at no charge by returning the product to Super Anchor Safety or to the distributor the product was purchased from.

Permanent Anchor Warranty

Super Anchor Safety warrants to the purchaser that all anchors sold as a permanent fixture with Hot Dip Galvanizing, Stainless Steel, and Thermo-Plastic finishes are fully warranted against failure due to defects in materials or workmanship for a period of five (5) years from the date of initial installation. SAS does not warranty the installation or flashing system used to waterproof the anchors. The SAS factory warranty is void if the product has been modified or has not been used in accordance with SAS specifications and instructions for that product. Anchors that have been removed from service due to re-roofing or remodel of the structure they were originally attached to must be inspected by an SAS factory representative or a competent person before being reinstalled.

See the Super Anchor Warranty and Compliance Statement (PDF) for the full manufacturer document.

0 Reviews Hide Reviews Show Reviews