Super Anchor Retro-Flash Flashing 10-Pack, 2401-A
The Super Anchor 2401-A is a 10-pack of Retro-Flash flashing plates: 20 gauge Dacromet coated zinc plated steel, 14 by 4 inches, used to flash a D-Minus or RS series roof anchor watertight after the roof is installed.
Retro-Flash is sold in contractor volume packs. Choose the 10-pack or 80-pack at checkout.
Who Needs This Product
Retro-Flash is a flashing accessory for roofers and building owners installing D-Minus or RS series anchors on an existing roof who need a watertight seal. It is a flashing component, not a fall-arrest anchor by itself.
Features
20 gauge steel plate
Durable 14 by 4 inch flashing plate.
Dacromet coated zinc plated
Corrosion resistant finish for long roof life.
Watertight retro-fit
Flashes the anchor watertight on a roof already installed.
Fits D-Minus and RS anchors
Sized for Super Anchor D-Minus and RS series anchors.
Slides under the shingle course
Sheds water over the anchor penetration.
Contractor volume packs
Sold in 10-pack and 80-pack quantities.
This is one component of a personal fall-arrest system. Retro-Flash is a flashing component. It does not replace the roof anchor and must be installed per the anchor instructions for a watertight seal. Inspect before each use and confirm compatibility, capacity, and fall clearance. Run the Fall Protection Calculator below before you tie off.
Compliance Standards
ANSI Z359
American National Standard for fall protection equipment.
OSHA 29 CFR 1926.502
Federal construction fall protection requirements.
Typical Applications
How to Use the Retro-Flash Flashing
Follow the Super Anchor Safety instruction manual. The sequence below is an overview only.
- Inspect. Check for wear, cuts, distortion, corrosion, and gate or hardware function before each use.
- Confirm compatibility. Verify the component, harness, and anchor are compatible and rated.
- Connect. Make the connection and confirm every gate is fully closed and locked.
- Verify. Confirm the full system, capacity, and fall clearance.
- Use. Work within the rated limits of the system.
Inspection and Retirement
Inspect before each use, with a documented competent-person inspection at least annually. Remove the product from service for any condition below.
- Webbing or body: cuts, frays, abrasion, burns, corrosion, or distortion.
- Stitching: pulled, cut, or broken threads.
- Gates and locks: proper close and lock function.
- Fall indicators: any sign of deployment.
- Labels: illegible or missing markings.
Retire the anchor immediately after any fall-arrest event, or if any inspection point fails.
Fall ProtectionDistributors, LLC Free Tool · No Signup · OSHA 1926.502 Free Interactive Tool Fall Protection Calculator Pick your system. Run the math. Generate a plan. 1Pick Your SystemDetermine fall restraint vs. fall arrest based on your work surface, edge access, and clearance. 2Run the MathCalculate exact fall clearance required below the work surface for your setup. 3Generate a PlanGet a printable OSHA-compliant Fall Protection Plan structured around 29 CFR 1926.502(k).
Technical Specifications
| SKU | 2401-A (10 flashings) |
|---|---|
| Type | Retro-Flash flashing plate |
| Size | 14 x 4 in |
| Material | 20 ga Dacromet coated zinc plated steel |
| Fits | D-Minus and RS series anchors |
| Use | Flashing accessory |
| Warranty | Super Anchor Safety manufacturer warranty; see Warranty tab |
Frequently Asked Questions
Retro-Flash Flashing Submittals and Documentation
Spiral Shank Nail Spec (PDF)Stainless fastener specifications for anchor installation. Retro Flashing Guide (PDF)Flashing installation guide for retro-fit anchors. Retro-Flash Flyer (PDF)Retro-Flash system overview and applications. Retro-Flash 2401-S Flyer (PDF)2401-S flashing details and installation. RS-10 D-Minus Flyer (PDF)RS-10 and D-Minus anchor family overview. Super Anchor Warranty and Compliance Statement (PDF)Manufacturer warranty and standards compliance.Related Super Anchor Products
Buying Retro-Flash in Volume?
Anchor type and quantity affect the order. Confirm your project with us and we will help you order the right flashing.
Call 863-703-4522 to talk to a fall protection specialist.
Super Anchor Safety Manufacturer Warranty
Super Anchor Safety (SAS) warrants to the purchaser that all products are free from defect in material and workmanship at the time of shipment. This warranty is limited to product replacement for a period of one (1) year from the date of installation or use by the owner, provided that this period shall not exceed two (2) years from the date of shipment. This warranty only covers defects in material and workmanship. It does not cover conditions resulting from normal wear, neglect, abuse, or accident. This product warranty does not cover oxidation of zinc, dacromet, or powder coatings used on permanent and temporary anchors that results from connector abrasion unless the coating can be shown to be defective at the time of purchase. This warranty is non-transferable. Any unused defective product will be replaced at no charge by returning the product to Super Anchor Safety or to the distributor the product was purchased from.
Permanent Anchor Warranty
Super Anchor Safety warrants to the purchaser that all anchors sold as a permanent fixture with Hot Dip Galvanizing, Stainless Steel, and Thermo-Plastic finishes are fully warranted against failure due to defects in materials or workmanship for a period of five (5) years from the date of initial installation. SAS does not warranty the installation or flashing system used to waterproof the anchors. The SAS factory warranty is void if the product has been modified or has not been used in accordance with SAS specifications and instructions for that product. Anchors that have been removed from service due to re-roofing or remodel of the structure they were originally attached to must be inspected by an SAS factory representative or a competent person before being reinstalled.
See the Super Anchor Warranty and Compliance Statement (PDF) for the full manufacturer document.
