Name: Super Anchor TrussBar Roof Anchor, Detent Pin, 2833-DP
Brand: Super Anchor
SKU: 2833-DP
Price: 218.4 USD
Availability: InStock

Description
Warranty Information
Reviews

Super Anchor Temporary Anchors

Super Anchor TrussBar Roof Anchor, Detent Pin, 2833-DP

When the house is finished, the roofer cuts off the straps and the TrussBar stays attached to the truss but is no longer usable. It is made from heavy duty mild steel with 2 foot tie-off straps, and two workers can use it for fall arrest. Choose the 2833 bolt attachment or the 2833-DP detent pin attachment.

5,000 lbMin Tensile Strength

2 PersonFall Arrest Capacity

310 lbMax User Weight

2 ftTie-Off Straps

2x4 and 2x6Fits Trusses

14,770 lbDetent Pin Strength

Deck OverFraming Anchor

TemporarySingle Use Anchor

Who Needs This Product

The TrussBar is a temporary roof anchor for production builders and framers who need a robust deck-over anchor point during framing and sheeting. It protects all trades through the sheeting stage and is disabled when the roof is finished. Complete the system with full-body harnesses and energy-absorbing connecting devices.

Features

Deck over design

Install on the truss, deck over the top, and the tie-off straps stay exposed for all trades.

Protects all trades

Provides tie-off points during framing and sheeting for everyone on the roof.

Two person fall arrest

Up to two workers can use the TrussBar for fall arrest.

Heavy duty mild steel

Robust steel construction with 2 foot tie-off straps.

Bolt or detent pin

Choose the 2833 bolt attachment or the 2833-DP detent pin attachment.

Disabled at completion

The roofer cuts the straps when the house is finished and the bar is no longer usable.

⚠

This is a temporary anchor, not a complete system. A personal energy absorber is required. Install onto framing capable of 5,000 lb, use full-body harnesses with connecting devices, and confirm fall clearance. Run the Fall Protection Calculator below before you tie off.

Compliance Standards

OSHA 29 CFR 1926.502

Federal construction fall protection anchorage requirements.

ANSI Z359.1

American National Standard for fall arrest components.

Typical Applications

Production framingDeck-over anchor during framing and sheeting.

Roof sheetingTie-off protection while decking.

Multifamily constructionAnchor points for all trades during the build.

Residential constructionTemporary fall protection during roofing.

How to Install the TrussBar

Follow the Super Anchor Safety instruction manual. The sequence below is an overview only.

Locate the anchors. Install the TrussBar onto trusses at predetermined locations per a competent-person layout.
Attach. Fasten with the bolt (2833) or the detent pin (2833-DP).
Use during framing. Tie off during the framing and sheeting stages.
Deck over. Deck over the top of the TrussBar and feed the tie-off straps up through or between the sheeting.
Disable at completion. The roofer cuts off the straps when the house is finished.

Inspection and Retirement

Inspect before each use, with a documented competent-person inspection at least annually. Remove the product from service for any condition below.

Anchor body: cracks, deformation, corrosion, or elongated holes.
Coating: worn or damaged galvanizing, dacromet, or powder coat at the connection point.
Fasteners and flashing: loose, missing, backed-out, or leaking hardware.
D-ring or connection point: burrs, sharp edges, or excessive wear.
Labels: illegible or missing product identification.

Retire the anchor immediately after any fall-arrest event, or if any inspection point fails.

Fall Protection
Distributors, LLC Free Tool · No Signup · OSHA 1926.502 Free Interactive Tool Fall Protection Calculator Pick your system. Run the math. Generate a plan. 1Pick Your SystemDetermine fall restraint vs. fall arrest based on your work surface, edge access, and clearance. 2Run the MathCalculate exact fall clearance required below the work surface for your setup. 3Generate a PlanGet a printable OSHA-compliant Fall Protection Plan structured around 29 CFR 1926.502(k). Run the Numbers and Stay Safe Launch the Calculator ›

Technical Specifications

SKU	2833-DP (detent pin attachment)
Manufacturer Part Number	2833 / 2833-DP
Type	Temporary deck-over roof anchor
Material	Heavy duty mild steel with 2 ft tie-off straps
Cross-bar	1-1/2 in by 1-1/2 in by 1/8 in square steel tube
Detent pins	3/8 in stainless steel, 14,770 lb tensile strength
Capacity	Up to 2 persons fall arrest or fall restraint
Min tensile strength	5,000 lb (22.5 kN)
Max user weight	310 lb (140 kg)
Fits	2x4 and 2x6 trusses
Standards	OSHA 1926.502 and 1910.66; ANSI Z359.1
Warranty	Super Anchor Safety manufacturer warranty; see Warranty tab

Frequently Asked Questions

What is the 2833-DP?

The Super Anchor 2833-DP TrussBar is the detent pin model of the temporary roof anchor for 2x4 and 2x6 trusses, blue powder coated, with two 6047-C 24 inch truss bar straps and detent pin hardware for fast, tool-free attachment. Only trained workers should select, install, and use fall protection equipment for its intended application. A qualified person should verify that the installation and the overall system meet the requirements of your specific job site.

For the 2833-DP, how does the deck-over design work?

You install the bar on the truss, deck over the top, and feed the tie-off straps up so they stay exposed for all trades until the roof is finished. Before every use, confirm the product is compatible with the rest of your fall protection system and that you have adequate fall clearance below the work area.

For the 2833-DP, how many workers can use it?

Up to two workers for fall arrest or fall restraint. Make sure the connecting hardware and anchorage suit your application before you attach a lanyard or lifeline. Store it in a clean, dry place away from heat and chemicals to help preserve its condition between uses.

Why choose the 2833-DP configuration?

The detent pin 2833-DP installs and moves without wrenches, which pays off for crews that reposition the bar through the framing sequence. Always inspect the product before each use and take it out of service if you notice any damage, deformation, or excessive wear. Before every use, confirm the product is compatible with the rest of your fall protection system and that you have adequate fall clearance below the work area.

For the 2833-DP, is an energy absorber required?

Yes. A personal energy absorber is required for each worker. Make sure the connecting hardware and anchorage suit your application before you attach a lanyard or lifeline. Only trained workers should select, install, and use fall protection equipment for its intended application.

For the 2833-DP, what happens to the bar when the roof is done?

The roofer cuts off the straps. The bar stays attached to the truss but is no longer usable. A correct installation is critical, so confirm the setup matches the manufacturer instructions before any worker ties off. Always inspect the product before each use and take it out of service if you notice any damage, deformation, or excessive wear.

What completes a system with the 2833-DP?

Yes. The anchor is an anchorage point only and must be paired with a full-body harness and a connecting device. Pair it only with connectors and equipment that are approved for use together so the complete system performs as designed. Keep the manufacturer instructions with the equipment so anyone using it can reference the approved procedures.

Super Anchor TrussBar Submittals and Documentation

Safety Truss Bar Manual 2023 (PDF)Use, installation, capacity, and inspection. Moveable Universal Safety Bar Guide (PDF)Safety bar application and use. Warranty and Compliance Statement (PDF)Manufacturer warranty and standards compliance.

Related Super Anchor Products

Framing a Production Roof?

Anchor spacing, truss size, and the number of trades all affect coverage. Confirm your job with us and we will help match the right TrussBar attachment and PPE.

Call 863-703-4522 to talk to a fall protection specialist.

Super Anchor Safety Manufacturer Warranty

Super Anchor Safety (SAS) warrants to the purchaser that all products are free from defect in material and workmanship at the time of shipment. This warranty is limited to product replacement for a period of one (1) year from the date of installation or use by the owner, provided that this period shall not exceed two (2) years from the date of shipment. This warranty only covers defects in material and workmanship. It does not cover conditions resulting from normal wear, neglect, abuse, or accident. This product warranty does not cover oxidation of zinc, dacromet, or powder coatings used on permanent and temporary anchors that results from connector abrasion unless the coating can be shown to be defective at the time of purchase. This warranty is non-transferable. Any unused defective product will be replaced at no charge by returning the product to Super Anchor Safety or to the distributor the product was purchased from.

Permanent Anchor Warranty

Super Anchor Safety warrants to the purchaser that all anchors sold as a permanent fixture with Hot Dip Galvanizing, Stainless Steel, and Thermo-Plastic finishes are fully warranted against failure due to defects in materials or workmanship for a period of five (5) years from the date of initial installation. SAS does not warranty the installation or flashing system used to waterproof the anchors. The SAS factory warranty is void if the product has been modified or has not been used in accordance with SAS specifications and instructions for that product. Anchors that have been removed from service due to re-roofing or remodel of the structure they were originally attached to must be inspected by an SAS factory representative or a competent person before being reinstalled.

See the Super Anchor Warranty and Compliance Statement (PDF) for the full manufacturer document.

0 Reviews Hide Reviews Show Reviews