3006 Hinged Temporary Roof Anchor, 4-Pack
The Super Anchor 3006 SAS-Hinge is the workhorse temporary roof anchor: an 11 gauge steel hinged anchor, yellow zinc or dacromet plated, with a 5,000 lb minimum tensile strength and a permanent date of manufacture stamp. The hinge conforms to the ridge, fasteners drive through the leg holes into framing, and the anchor removes when the job is done. This listing is a 4-pack.
One worker at up to 340 lb including tools in a personal fall arrest system, on slopes to 20/12 with #12 wood screws or 12/12 with 16d nails. Horizontal lifelines may run between 3006 anchors when engineered by a qualified person per the Hinge HLLS manuals. Compliant with OSHA 1926.502 and 1910.66, ANSI Z359.1-07 and A10.32-2012, and certified for Quebec.
Who Needs This Product
The 3006 is the anchor roofing crews nail at the ridge on day one and pull when the last course is in: framers, roofers, gutter crews, and punch-out trades on wood framed residential and light commercial jobs. Each worker wears a full body harness with an ANSI or CSA compliant personal energy absorber connected by lifeline or SRL. It is temporary only, removed after use, and not intended for permanent installation.
Features
Hinged ridge design
The hinge folds over the ridge or works on the field of the roof, conforming to the pitch on either side.
5,000 lb, 11 gauge steel
Plated 11 gauge steel with a 5,000 lb minimum tensile strength and permanent date stamp.
Fast on, fast off
Nails or screws through the leg holes install it in a minute, and it removes clean at job end for the next roof.
Slope rated to 20/12
#12 wood screws carry it to 20/12; 16d nails to 12/12 per the 2022 manual.
HLL capable when engineered
Anchors horizontal lifelines between anchors when designed by a qualified person per the Hinge HLLS manuals.
Retail packaged 4-pack
Four anchors with instructions, ready for the crew truck.
Technical Specifications
| Model | SAS-Hinge No. 3006 |
|---|---|
| Package | 4-pack |
| Material | 11 gauge steel, yellow zinc or dacromet plated |
| Minimum Tensile Strength | 5,000 lb |
| User Capacity | 1 person at 340 lb maximum including tools |
| Maximum Slope | 20/12 with #12 wood screws; 12/12 with 16d nails |
| Duty Cycle | Temporary installation only, remove after use |
| Horizontal Lifelines | Permitted when engineered by a qualified person per Hinge HLLS manuals |
| PPE Requirement | ANSI or CSA compliant harness and personal energy absorber required |
| Compliance | OSHA 1926.502 and 1910.66; ANSI Z359.1-07; ANSI A10.32-2012; certified for use in Quebec |
| Traceability | Permanent date of manufacture stamp YYYY-MM |
Temporary anchor only. The 3006 is not intended for permanent installation. Match the fastener to the slope: #12 wood screws to 20/12, 16d nails only to 12/12. The framing must carry the fall protection load, sheathing follows the framing requirements in the manual, and every worker uses a personal energy absorber. Remove the anchor after use.
Compliance Standards
ANSI Z359.1-07 / A10.32-2012
Temporary anchorage compliance per the 2022 SAS-Hinge manual.
OSHA 1926.502 / 1910.66
Construction fall protection and powered platform anchorage criteria.
Quebec Certified
Certified by a member of l'Ordre des ingenieurs du Quebec.
Stamped Traceability
Permanent YYYY-MM date of manufacture stamp on every anchor.
Typical Applications
Installation Overview
Full figures and fastener specifications are in the manual linked below. The basics:
- Set the anchor at the ridge or on the field with the hinge conforming to the pitch, at locations per the job specific plan.
- Fasten through the leg holes into framing: #12 wood screws for slopes to 20/12, or 16d nails to 12/12.
- Confirm the framing carries the fall protection load and sheathing is installed per the manual before tie-off.
- Connect the lifeline or SRL with ANSI or CSA compliant connectors and a personal energy absorber.
- Work within the fall protection service zones in the manual, rigging fall restraint where free fall exposure exists.
- Remove the anchors when the work is complete; they are reusable across jobs while they pass inspection.
Inspection and Retirement
Inspect before installation and each use, with documented annual inspections. Remove the anchor from service when any of the following apply:
- The anchor is bent, cracked, or deformed.
- Fastener holes are elongated or torn.
- The anchor was subjected to a fall.
- The date stamp is unreadable or plating is corroded through.
- Fasteners were reused or the wrong type was used for the slope.
Tag anchors removed from service to prevent further use until inspected by a qualified or competent person.
Fall ProtectionDistributors, LLC Free Tool · No Signup · OSHA 1926.502 Free Interactive Tool Fall Protection Calculator Pick your system. Run the math. Generate a plan. 1Pick Your SystemDetermine fall restraint vs. fall arrest based on your work surface, edge access, and clearance. 2Run the MathCalculate exact fall clearance required below the work surface for your SRL or lanyard setup. 3Generate a PlanGet a printable OSHA-compliant Fall Protection Plan structured around 29 CFR 1926.502(k).
Frequently Asked Questions
Product Submittals and Documentation
Hinge Anchor 3006 Manual (PDF)Installation and removal for the 3006 hinged anchor. Super Anchor Warranty and Compliance Statement (PDF)Manufacturer warranty and standards compliance.Compatible and Related Products
- Super Anchor 3013-D Hinge-2 Anchors. Adjustable reusable temporary anchor with forged D-ring.
- Super Anchor 3006 Hinged Anchors. Value hinged temporary anchor 4-pack.
- Super Anchor 4020 3-Strand Value Lifeline. Lifeline for temporary anchor tie-off.
- Super Anchor 3200 50 ft Safety Kit. Complete roofers kit built on the Hinge-2 anchor.
Outfitting a Roofing Crew with Temporary Anchors?
Tell us the crew size and slopes you work and we will spec anchors, lifelines, and kits so everything ships together, based on the delivery location.
Call 863-703-4522 to talk to a fall protection specialist.
Super Anchor Safety Manufacturer Warranty
Super Anchor Safety (SAS) warrants to the purchaser that all products are free from defect in material and workmanship at the time of shipment. This warranty is limited to product replacement for a period of one (1) year from the date of installation or use by the owner, provided that this period shall not exceed two (2) years from the date of shipment. This warranty only covers defects in material and workmanship. It does not cover conditions resulting from normal wear, neglect, abuse, or accident. This product warranty does not cover oxidation of zinc, dacromet, or powder coatings used on permanent and temporary anchors that results from connector abrasion unless the coating can be shown to be defective at the time of purchase. This warranty is non-transferable. Any unused defective product will be replaced at no charge by returning the product to Super Anchor Safety or to the distributor the product was purchased from.
Permanent Anchor Warranty
Super Anchor Safety warrants to the purchaser that all anchors sold as a permanent fixture with Hot Dip Galvanizing, Stainless Steel, and Thermo-Plastic finishes are fully warranted against failure due to defects in materials or workmanship for a period of five (5) years from the date of initial installation. SAS does not warranty the installation or flashing system used to waterproof the anchors. The SAS factory warranty is void if the product has been modified or has not been used in accordance with SAS specifications and instructions for that product. Anchors that have been removed from service due to re-roofing or remodel of the structure they were originally attached to must be inspected by an SAS factory representative or a competent person before being reinstalled.
See the Super Anchor Warranty and Compliance Statement (PDF) for the full manufacturer document.
