FallTech Cable Carabiner Sling Anchor with Galvanized Steel Cable
The FallTech Cable Carabiner Sling Anchor is a galvanized steel wire-rope anchor fitted with an alloy-steel carabiner and D-ring. Wrap the cable around a rated structure and clip the carabiner back to the D-ring to form a fast, secure loop anchor.
The carabiner connection makes it quick to install and remove, and the steel cable resists cuts and abrasion. Rated for 5,000 lb (22.2 kN) and certified to ANSI Z359.18-2017. Choose from lengths of 6', 8', 10', 12' to fit the member.
Who Needs This Product
This product is a cable carabiner sling anchor, the anchorage component of a personal fall arrest system. Crews who want a fast, clip-on loop anchor wrap it around a rated member and snap the carabiner to the D-ring, then connect an SRL or lanyard. You still need a certified full-body harness and a compatible connecting device to complete the system.
Features
Carabiner connection
Alloy-steel carabiner clips to the D-ring for a fast, secure loop.
Steel wire rope
Galvanized cable resists cuts and abrasion better than webbing.
Quick to install
Snaps on and off faster than a pass-through cinch.
Several lengths
Available from 6 ft to 12 ft to fit the member.
Reusable and portable
Stows easily in a gear bag between jobs.
ANSI Z359.18-2017
Certified anchorage rated for 5,000 lb (22.2 kN).
Confirm the carabiner is locked and the structure is rated. Make sure the carabiner gate is fully closed and locked, the structure supports at least 5,000 lb, and edges are not sharp. Confirm fall clearance and swing-fall with the Fall Protection Calculator below.
Compliance Standards
ANSI Z359.18-2017
American National Standard for anchorage connectors. 5,000 lb (22.2 kN).
OSHA 29 CFR 1926.502
Federal construction fall protection anchorage requirements.
OSHA 29 CFR 1910
General industry personal fall protection requirements.
5,000 lb rated
Minimum breaking strength of 5,000 lb (22.2 kN).
Typical Applications
How to Install
Follow the FallTech instruction manual. The sequence below is an overview only.
- Inspect. Check the webbing, stitching, and hardware for damage before each use.
- Choose a rated anchor point. Confirm the structure supports at least 5,000 lb and is free of sharp or abrasive edges.
- Wrap the structure. Pass the anchor around the beam, column, or member in the approved configuration.
- Connect. Attach your SRL or energy-absorbing lanyard to the anchor connection point.
- Check clearance. Confirm fall clearance and swing-fall with the calculator below.
Inspection and Retirement
Inspect before each use, with a documented competent-person inspection at least annually. Remove the anchor from service for any of the conditions below.
- Wire rope: kinks, birdcaging, broken wires, corrosion, or crushing.
- Swages and thimbles: cracks, slippage, or deformation.
- Hardware (carabiner, hook, D-ring, or O-ring): deformation, corrosion, or a gate that will not lock.
- Coating (if present) and labels: heavy damage, or illegible markings.
Remove the anchor from service immediately after any fall-arrest event, and destroy retired equipment so it cannot return to service.
Fall ProtectionDistributors, LLC Free Tool · No Signup · OSHA 1926.502 Free Interactive Tool Fall Protection Calculator Pick your system. Run the math. Generate a plan. 1Pick Your SystemDetermine fall restraint vs. fall arrest based on your work surface, edge access, and clearance. 2Run the MathCalculate exact fall clearance required below the work surface for your lanyard or SRL setup. 3Generate a PlanGet a printable OSHA-compliant Fall Protection Plan structured around 29 CFR 1926.502(k).
Technical Specifications
| Type | Cable carabiner sling anchor |
|---|---|
| Material | Galvanized steel wire rope, alloy-steel carabiner and D-ring |
| Anchorage classification | ANSI Z359.18-2017 |
| Minimum breaking strength | 5,000 lb (22.2 kN) |
| Capacity (ANSI) | One worker, up to 310 lb combined |
| Lengths available | 6', 8', 10', 12' |
| Connection | Carabiner to D-ring loop |
| Standards | ANSI Z359.18-2017; OSHA 1926.502 and 1910 |
| Packaging | Sold in multi-packs. Pack quantity is set per length so each pack is an economical order; choose your length and pack size in the options above. |
| Warranty | FallTech 2-year limited warranty against defects in materials and workmanship |
Frequently Asked Questions
FallTech CCS Submittals and Documentation
84202D Instruction Manual (PDF)Installation, application limits, capacity, and inspection. 84202D Declaration of Conformity, ANSI (PDF)Certification to ANSI Z359.18-2017 (FallTech test lab). 84202D Spec Sheet (PDF)One-page specifications and compliance summary.Related Anchors
- FallTech steel and beam anchors. See the full beam clamp and steel anchor line.
- FallTech fall protection equipment. Harnesses, SRLs, lanyards, and anchors.
Specifying Anchor Slings for Your Crew?
The sling, the connecting device, and the harness all have to match the structure, the edges, and the fall clearance below. Confirm your application with us and we will help you pick the right length and style.
Call 863-703-4522 to talk to a fall protection specialist.
