HH05SW ToolGrip 5 lbs Swiveling Hammer Holster, 5-Pack
The Frontline HH05SW carries the hammer so your hand does not have to: a swiveling holster that follows your body as you climb, crouch, and work - no handle jabbing your ribs - with secure retention and convenient hands-free carrying on the job.
Built from high-quality polyester at 7 in x 8 in with a metal D-ring, the holster adds side D-rings as additional attachment points for tethers, and carries a 5 lb safe working capacity.
Who Needs This Product
This product is dropped-object prevention equipment from the Frontline ToolGrip line. Crews working at height tether their tools so a slip never becomes a struck-by incident below. ToolGrip products are rated for tools only - personal fall protection is a separate system.
Features
Swivels with you
The holster pivots as you move - the handle follows your leg instead of fighting it.
Secure retention
Holds the hammer through climbs and crouches.
Side D-rings
Extra attachment points put a tether right at the holster.
Hands-free carry
The hammer rides ready without occupying a hand.
5 lb capacity
Framing hammers to small sledges.
Tether-ready
Pair with a TLS15 so the hammer is covered in and out of the holster.
Technical Specifications
| SKU | HH05SW |
|---|---|
| Type | Swiveling hammer holster |
| Safe working capacity | 5 lbs |
| Dimensions | 7 in W x 8 in L |
| Webbing | High-quality polyester |
| D-rings | Metal, side-mounted |
| Feature | Swiveling holster body |
Tool tethering equipment only - NEVER personal fall protection. ToolGrip products are rated for tools, in the capacities on the spec sheet. Never connect any ToolGrip component to a personal fall arrest or restraint system, and never exceed the rated tool weight.
Compliance Standards
ANSI/ISEA 121-2018
American National Standard for dropped object prevention solutions - the consensus standard for tool tethering equipment.
OSHA 1926.759
Falling object protection requirements in steel erection; tethering supports compliance.
OSHA General Duty Clause
Dropped-tool struck-by incidents are routinely cited under 5(a)(1); tethering is the recognized control.
Typical Applications
How to Set Up the HH05SW
Follow the manufacturer's manual. The sequence below is an overview only.
- Inspect. Check fabric, stitching, D-rings, and the swivel before each use.
- Mount on the belt. Position the holster on your dominant side per the manual.
- Tether the hammer. Clip a ToolGrip tether from a side D-ring to the hammer.
- Holster and check. Seat the hammer and confirm retention.
- Tug test. Verify tether and mount before working at height.
Inspection and Retirement
Inspect before each use. Pull the equipment from service for any of the conditions below.
- Webbing and elastic: cuts, fraying, abrasion, burns, or loss of elasticity.
- Stitching: broken, pulled, or abraded threads.
- Hardware: deformation, cracks, corrosion, or gates and locks that fail to close.
- Attachment points: loose tape bonds, worn loops, or damaged D-rings.
- Markings: labels must be present and legible.
Remove from service immediately if any inspection point fails or after the tether arrests a dropped tool with visible damage. ToolGrip products are tool tethering equipment - never use them for personal fall protection.
Frequently Asked Questions
Frontline HH05SW Submittals and Documentation
Frontline HH05SW Spec Sheet (PDF)Dimensions, capacity, materials, and features. HH05SW-5PK Frontline ToolGrip User Manual (PDF)Use, limitations, inspection, and retirement for the ToolGrip tool tethering line. HH05SW-5PK Frontline ToolGrip Quick Display Guide (PDF)Line overview of the ToolGrip tool tethering family. HH05SW-5PK Frontline Catalog (PDF)The full Frontline Fall Protection product catalog.Compatible and Related Products
- Frontline TLS15 Elastic Tool Tether. Tether the hammer from the side D-ring.
- Frontline BP10L Large Tool Pouch. Pouch storage beside the holster.
- Frontline WB05 Tool Wrist Band. Wrist tethering for in-hand work.
Building a Dropped-Object Program?
Tethers, anchors, holsters, and pouches work as a system. Confirm your tool list and working heights with us and we will walk through the ToolGrip lineup so the right equipment ships together.
Call 863-703-4522 to talk to a fall protection specialist.
