PSSW2R-US Patriot Positioning Chain with Swiveling Hook, Made in USA
The Frontline PSSW2R-US is the Patriot edition of the rebar positioning chain - proudly made in the USA using US and imported components, for crews and contracts that spec American-made equipment.
High strength 1/4 in twist link zinc plated chains meet a forged galvanized steel swivel and zinc chromate plated forged alloy steel double locking snaphooks and rebar hook - every hook 100 percent proof load tested. 22 in bearing to bearing, 310 lb user capacity, manufactured and tested by a UL registered ISO 9001:2015 firm to ANSI A10.32, OSHA 1910 and 1926.
Who Needs This Product
This product is a rebar positioning chain assembly - the ironworker's third hand. Clip the swivel rebar hook to the curtain, lean back into the harness side D-rings, and both hands are free to tie. Chain shrugs off the hot, abrasive, torch-adjacent work that destroys webbing positioning devices. Use with a harness positioning system; a separate fall arrest system is still required.
Features
Made in the USA
Manufactured in the USA using US and imported components - letter in Submittals.
Twist link chain
1/4 in zinc plated twist link lies flat against the body.
Double locking hooks
Forged alloy steel snaphooks and rebar hook, zinc chromate plated.
100 percent proof loaded
Every hook is individually load tested for quality assurance.
Forged swivel
Galvanized steel swivel keeps the chain from winding up.
Patriot line
Matches the Patriot harnesses, lanyards, and tripods for Buy American specs.
Technical Specifications
| SKU | PSSW2R-US |
|---|---|
| Type | Positioning chain with swiveling rebar hook, Made in USA |
| Chain | High strength 1/4 in twist link, zinc plated |
| Hooks | Zinc chromate plated forged alloy steel, double locking; 100 percent proof load tested |
| Swivel | Forged galvanized steel |
| Length | 22 in bearing to bearing |
| User capacity | 310 lbs |
| Quality system | UL registered ISO 9001:2015 firm |
| Country of manufacture | USA (US and imported components) |
| Standards | ANSI A10.32; OSHA 1910; OSHA 1926 |
Positioning is not fall arrest. A positioning chain holds you in place at the work - it does not catch a fall. OSHA requires an independent personal fall arrest system in addition to positioning. Inspect the chain, hooks, and swivel before each use, and connect only per the Frontline manual.
Compliance Standards
ANSI A10.32
Fall protection requirements for construction and demolition operations.
OSHA 29 CFR 1926.502
Federal construction fall protection criteria, including positioning device requirements.
OSHA 29 CFR 1910
General industry requirements.
Typical Applications
How to Use the PSSW2R-US
Follow the manufacturer's manual. The sequence below is an overview only.
- Inspect. Check chain, hooks, swivel, and gates before each use.
- Connect to the work. Clip the swivel rebar hook over the rebar or member.
- Connect to the harness. Snap the side hooks to both positioning D-rings.
- Load and lean. Set your stance and lean into the system - hands free.
- Keep arrest separate. Maintain your independent fall arrest connection at all times.
Inspection and Retirement
Inspect before each use, with a documented competent-person inspection at least every 6 months. Pull the equipment from service for any of the conditions below.
- Chain links: stretch, deformation, nicks, gouges, or corrosion.
- Hooks: deformation, cracks, corrosion, or gates that fail to close and double-lock.
- Swivel: free rotation, no play or cracking at the bearing.
- Connection points: wear at the union and end fittings.
- Markings: labels must be present and legible.
Retire the assembly immediately after any fall event, any dropped-load shock, or if any inspection point fails. Destroy retired equipment so it cannot return to service.
Fall ProtectionDistributors, LLC Free Tool · No Signup · OSHA 1926.502 Free Interactive Tool Fall Protection Calculator Pick your system. Run the math. Generate a plan. 1Pick Your SystemDetermine fall restraint vs. fall arrest based on your work surface, edge access, and clearance. 2Run the MathCalculate exact fall clearance required below the work surface for your SRL or lanyard setup. 3Generate a PlanGet a printable OSHA-compliant Fall Protection Plan structured around 29 CFR 1926.502(k).
Frequently Asked Questions
Frontline PSSW2R-US Submittals and Documentation
Frontline PSSW2R-US Spec Sheet (PDF)Chain, hardware, length, capacity, and standards. Frontline PSSW2R-US User Manual (PDF)Work positioning device use, limitations, inspection, and retirement. Frontline Made in USA Letter (PDF)Manufacturer letter confirming the products made in the USA using US and imported components. Frontline Catalog (PDF)The full Frontline Fall Protection product catalog.Compatible and Related Products
- Frontline PSSW2R Rebar Positioning Chain. The imported version of the same assembly.
- Frontline LIS62R Twin Leg Rebar Lanyard. The fall arrest connection to pair with positioning.
- Frontline 100CTB Combat Construction Harness. The construction harness to complete the system.
Outfitting Rodbusters?
Positioning chains, twin leg lanyards, and harnesses work as a system. Confirm your application, anchorage, and clearance with us and we will walk through the kit list so the right equipment ships together.
Call 863-703-4522 to talk to a fall protection specialist.
