QuickPick Standard Rescue Kit with 4:1 Hauling
The QuickPick answers the minutes after a fall arrest: the rescuer stays anchored, reaches the suspended worker remotely with the rescue pole, connects, and hauls with a 4:1 mechanical advantage. Everything lives in one kit bag with no assembly, only an overhead anchor required.
Compliant with OSHA and ANSI Z359.4-2013 for assisted rescue and self-rescue, rated for a 310 lb rescued worker. The standard kit configuration serves teams experienced in rescue.
Who Needs This Product
OSHA requires prompt rescue wherever fall arrest is used, and suspension trauma sets the clock in minutes. The QuickPick converts that obligation from a plan on paper to a bag on the rack: pole-connect from safety, raise to release the tension, then raise or lower the worker to the rescue level.
Features
Remote Attachment Pole
The rescuer connects to the suspended worker from a safe, anchored position.
4:1 Mechanical Advantage
One rescuer hauls a suspended worker with manageable effort.
Raise or Lower
The system moves the worker in either direction to reach the rescue level.
Complete, Assembled Kit
Pulleys, rope, pole, control handle, carabiners, anchor strap, tool lanyard, and bags, ready out of the bag.
Pigtail Rope Control
The control handle manages the load line smoothly during the lift or lower.
Economical Standard Trim
The experienced-team configuration keeps the price accessible for every site.
Technical Specifications
| SKU | QP-1/25FT |
|---|---|
| Product | QuickPick Standard Rescue Kit |
| Stocked length | 25 ft |
| Hauling | 4:1 mechanical advantage |
| Capacity | 310 lb rescued worker |
| Contents | Pulleys, rope, rescue pole with clip, pigtail control handle, carabiners, cross-arm strap, WristBandit tool lanyard, kit and pole bags |
| Standards | OSHA; ANSI Z359.4-2013 assisted rescue and self-rescue |
| Warranty | Miller Limited Lifetime Warranty against defects in workmanship and materials |
The anchor is only as good as the structure. Connect only to members that meet OSHA anchorage strength, position to minimize free fall and swing, and inspect before every use.
Compliance Standards
OSHA 1926.502 Anchorage
Anchorages for fall arrest must support 5,000 lb per worker attached, or maintain a safety factor of two under a qualified person.
ANSI Z359 Practice
Anchorage connectors follow ANSI Z359 component practice with 5,000 lb rated hardware.
ANSI Z359.2
Kept in service through pre-use checks and documented competent person inspections at least annually.
Typical Applications
Setup Overview
- Inspect the anchor and hardware before use.
- Select structure that meets OSHA anchorage strength for fall arrest.
- Install the anchor per the instructions for the structure type.
- Connect the lanyard or SRL and verify gates lock.
- Verify fall clearance and swing fall exposure before working.
Full installation instructions ship with the product.
Inspection and Retirement
Inspect before each use and have a competent person inspect at least annually per ANSI Z359.2.
- Webbing or body: cuts, frays, corrosion, cracks, distortion, or damage.
- D-rings and hooks: no cracks, corrosion, distortion; gates lock where fitted.
- Stitching and fasteners: intact and tight.
- Labels: present and legible.
Retirement triggers: any fall arrest loading, any defect found during inspection, or failure to verify fitness for service.
Fall ProtectionDistributors, LLC Free Tool · No Signup · OSHA 1926.502 Free Interactive Tool Fall Protection Calculator Pick your system. Run the math. Generate a plan. 1Pick Your SystemDetermine fall restraint vs. fall arrest based on your work surface, edge access, and clearance. 2Run the MathCalculate exact fall clearance required below the work surface for your SRL or lanyard setup. 3Generate a PlanGet a printable OSHA-compliant Fall Protection Plan structured around 29 CFR 1926.502(k).
Frequently Asked Questions
Miller QP-1/25FT Submittals and Documentation
QP-1 Specification Sheet (PDF)Technical data, ratings, and SKU-level UPC information. Miller Fall Protection Catalog (PDF)The full Miller line: body wear, connecting devices, anchors, and rescue. QP-1 Anchor Inspection Form (PDF)Printable pass/fail checklist for documented anchor inspections.Compatible and Related Products
- Miller Relief Step Suspension Trauma Strap, 3-Pack. Buys time on every harness while the QuickPick deploys.
- Miller 8183 Cross-Arm Strap. Spare anchorage for the rescue rig.
- Miller MightEvac SRL Rescue Kit with 7 ft Tripod. The retrieval answer for confined space entries.
Anchoring Your Fall Protection System?
Structure type, strength, and position decide the right anchor. Confirm your conditions with us and we will make sure the right equipment ships together, based on the delivery location.
Call 863-703-4522 to talk to a fall protection specialist.
Miller Limited Lifetime Warranty
Miller Fall Protection products are covered by the Miller Limited Lifetime Warranty. In the manufacturer's words: "We sincerely believe that our fall protection equipment is the best in the world. Our products endure rigorous tests to ensure that the fall protection equipment you trust is manufactured to the highest standards. Miller fall protection products are tested to withstand normal wear and tear, but are not indestructible and can be damaged by misuse."
In the unlikely event that you should discover defects in either workmanship or materials, under the Limited Lifetime Warranty, Miller will repair or replace the product at the manufacturer's expense. If a replacement is necessary and your product is no longer available, a comparable product will be substituted. The Limited Lifetime Warranty does not apply to normal wear and tear or abusive treatment of the product.
Miller is a brand of Protective Industrial Products, Inc. (PIP). Should a product issue surface, contact Fall Protection Distributors, LLC and we will coordinate the warranty claim with the manufacturer.
