Safety Helmet Visors - Clear or Tinted
Malta Dynamics Safety Helmet Visors add a flip-up layer of eye protection to your Malta Dynamics safety helmet. Made from durable, high-strength plastic, they meet the ANSI/ISEA Z87.1-2015 impact-resistance standard and feature an anti-scratch lens and an easy-clean rimless design. They install and remove from the helmet as needed and pivot on a hinge so the visor is there when you need it and stowed when you do not.
Choose clear or tinted. The tinted visor is 99% UV resistant to shield the eyes from the sun. Because the visor attaches to a helmet with a chin strap, it frees your hands from adjusting safety glasses, keeps the lens off your face, and prevents it from falling off. Clean with warm water and soap, no special chemicals required.
Who Needs This Product
These helmet visors are integrated flip-up eye protection for any crew already wearing Malta Dynamics safety helmets who want hands-free, off-the-face eye protection instead of separate safety glasses. The clear visor suits general work; the tinted visor adds 99% UV protection for outdoor and bright conditions. The visor mounts to the helmet's visor holes, so each worker needs a compatible Malta Dynamics safety helmet, sold separately.
Features
Clear or tinted lens
Choose a crystal-clear visor for general work or a tinted visor with 99% UV resistance for outdoor and bright conditions.
ANSI Z87.1-2015 impact
Made from durable high-strength plastic that meets the ANSI/ISEA Z87.1-2015 impact rating standard.
Hinged flip-up design
The hinge lets you position the visor where it sits, flip it down when needed, and push it up out of the way when not.
Hands-free, off-the-face
Attached to a helmet with a chin strap, the visor frees your hands and keeps the lens off your face with no temple pressure.
Anti-scratch rimless lens
An anti-scratch lens with an easy-clean rimless design cleans up with just warm water and soap.
Tool-free install
Visors install and remove from the safety helmet as needed using the included brackets and screws.
Technical Specifications
| SKU | MHTV0001 (Clear HTV0001; Tinted HTV0002) |
|---|---|
| Type | Flip-up safety helmet visor (eye protection) |
| Lens options | Clear or tinted |
| Material | Durable high-strength plastic |
| Lens coating | Anti-scratch |
| Design | Rimless, easy-clean |
| Tinted UV protection | 99% UV resistant (tinted visor) |
| Mounting | Hinged; installs and removes from the safety helmet visor holes |
| Hardware | Includes brackets and screws for installation |
| Helmet compatibility | Malta Dynamics safety helmets (sold separately) |
| Cleaning | Warm water and soap; no special chemicals |
| Compliance | ANSI/ISEA Z87.1-2015 impact rating |
| Conformity | Declaration #MD3P329 (Clear); #MD3P330 (Tinted), ISO 17025 third-party tested |
| Warranty | 1 year limited (Malta Dynamics) against factory defects in workmanship and materials |
A helmet visor is eye protection, not the whole system. The visor meets the ANSI Z87.1-2015 impact rating and provides eye protection, but for face protection against heavy debris, splash, or arc flash, use the appropriate face shield. Install per the instructions so the visor swivels freely but stays secure, and replace the visor immediately if it is cracked, deeply scratched, or has taken a forcible impact.
Compliance Standards
ANSI/ISEA Z87.1-2015
American National Standard for occupational eye and face protection; the visor meets the impact rating.
OSHA 29 CFR 1910.133
OSHA eye and face protection requirements for general industry.
99% UV (tinted)
The tinted visor is 99% UV-resistant for protection against the sun during outdoor work.
ISO 17025 tested
Conformity is declared with independent third-party laboratory testing under ISO 17025 accreditation.
Typical Applications
Installation Overview
Install per the Malta Dynamics helmet visor installation instructions. The sequence below is an overview only.
- Gather parts. Remove the visor, two screws, two internal plastic brackets, and two external plastic brackets from the bag.
- Insert internal brackets. Push the left and right internal brackets into the slots inside the helmet at the visor holes.
- Place external brackets. Fit the left and right external brackets over the brim at the pre-drilled visor holes.
- Snap on the visor. Place the clear or tinted visor over the external brackets so the tab snaps into the hole in the visor.
- Thread the screws. Thread one screw on each side from the inside out into the visor bracket; do not over-tighten so the visor can still swivel.
- Check the swivel. Confirm the visor flips up and down smoothly and holds position; then it is ready for use.
Inspection and Retirement
Inspect before each use. Remove the visor from service if any of the conditions below apply.
- Lens: cracks, deep scratches, or crazing that impairs vision or protection.
- Hinge and brackets: cracks, looseness, or a hinge that will not hold position.
- Screws: loose, stripped, or missing hardware.
- Tint: any degradation of the tinted visor's UV protection.
- Fit: a visor that no longer seats securely on the helmet.
Retirement triggers: any forcible impact to the visor, any cracked or deeply scratched lens, or any bracket or hinge that will not hold the visor securely. Replace the visor immediately at any sign of damage.
Fall ProtectionDistributors, LLC Free Tool · No Signup · OSHA 1926.502 Free Interactive Tool Fall Protection Calculator Pick your system. Run the math. Generate a plan. 1Pick Your SystemDetermine fall restraint vs. fall arrest based on your work surface, edge access, and clearance. 2Run the MathCalculate exact fall clearance required below the work surface for your SRL or lanyard setup. 3Generate a PlanGet a printable OSHA-compliant Fall Protection Plan structured around 29 CFR 1926.502(k).
Frequently Asked Questions
Malta Dynamics Safety Helmet Visors Submittals and Documentation
Malta Dynamics Safety Helmet Visors Spec Sheet (PDF)Helmet and visor part numbers, weights, features, and ANSI Z87.1 compliance. Malta Dynamics Safety Helmet Visors Installation Instructions (PDF)Step-by-step bracket and visor installation onto the safety helmet. Malta Dynamics HTV0001 Clear Visor Declaration of Conformity (PDF)ANSI/ISEA Z87.1-2015 conformity with ISO 17025 third-party testing (Clear). Malta Dynamics HTV0002 Tinted Visor Declaration of Conformity (PDF)ANSI/ISEA Z87.1-2015 conformity with ISO 17025 third-party testing (Tinted).Compatible and Related Products
- Malta Dynamics APEX Type 2 Class C Safety Helmet. The vented safety helmet these visors install onto.
- Malta Dynamics APEX Type 2 Class E Full Brim Safety Helmet. A full-brim safety helmet platform for the crew.
- Malta Dynamics APEX Safety Glasses. Standalone primary eye protection as an alternative or backup.
- Malta Dynamics APEX Safety Goggles. Sealed eye protection for dust and splash tasks.
Specifying Eye and Face Protection for Your Crew?
Need helmets and visors matched for your whole crew? Tell us your helmet model and how many clear versus tinted you need and we will build the kit so the right gear ships together.
Call 863-703-4522 to talk to a fall protection specialist.
